How to test the camshaft position sensor p0341?
Testing the camshaft position sensor and/or diagnostic trouble code (DTC) P0341, on your 3.8L V6 equipped GM car or mini-van, is an easy test that can be done using only a multimeter. No scan tool is needed for this test!
What does it mean when your engine code is p0341?
A code P0341 may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM NOTE: In some cases this engine code is generated on vehicles that do not actually have a camshaft position sensor.
How much does it cost to repair a p0341 Pontiac engine light?
The cost of diagnosing the P0341 PONTIAC code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
What is the camshaft position sensor on a Pontiac?
On some Pontiac models the camshaft position sensor is part Ignition Control Module (ICM) (aka igniter). If playback doesn’t begin shortly, try restarting your device.
What is the p0341 code for Camshaft Position Sensor?
P0341 code is triggered when the powertrain control module (PCM) detects a problem with the signal being sent by the camshaft position sensor. To learn more about how the ECM/PCM uses signals from the CMP, you can read our in-depth explanation here.
What does the p0341 OBD-II trouble code mean?
What the P0341 code means P0341 is an OBD-II generic code that says the engine control module (ECM) detected the engine camshaft position sensor circuit is not within specifications. The sensor pulses do not correlate to the pulses of the crankshaft sensor. What causes the P0341 code?
What is the diagnostic code for Camshaft Position Sensor?
Cost of diagnosing the P0341 code P0341 is a diagnostic trouble code (DTC) for “Camshaft Position Sensor Circuit Range/Performance”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What is the cam code on a 2004 Monte?
2004 Monte, No Cam signal, Code P0341 but starts and runs… Long story short the cam sensor wires were pinched and shorted by the power steering pump on a 3.4L. The car would not start and there were no trouble codes. Finally I notice no cam signal on the scanner so I started to dig. I found the cam sensor wires to be shorted out.
What does the CPS trouble code p0342 mean?
Trouble codes P0335 through P0349 are all generic codes related to the CPS inferring different reasons for the failure. In this instance, code P0342 infers the sensor’s signal is to low, or not strong enough. The signal is low enough to be vague and difficult to interpret. P0342 refers to the Bank 1 “A” sensor.
Why is my DTC p0341 CMP sensor not working?
Depending on year, make, and model, DTC P0341 or P0346 may have number of causes. Here are some of the most common. Faulty Sensor – If the sensor coil is open or shorted, then it will generate no signal. Poor Installation – A good CMP signal is highly dependent on placement.
What causes a p0342 DTC on a Mustang GT?
Ford Trucks / Mustang GT – An alternator phase problem, such as a blown diode or open coil, may cause so much electrical interference that the CMP signal gets distorted, causing a P0342 / P0347 DTC to set, among others, in spite of there being no actual problem with the CMP sensor or wiring.
Testing the camshaft position sensor and/or diagnostic trouble code (DTC) P0341, on your 3.8L V6 equipped GM car or mini-van, is an easy test that can be done using only a multimeter. No scan tool is needed for this test!
What causes the p0341 Chevrolet engine code to change?
The change in the magnetic field cause the voltage from the sensor to change. When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals. Need more information on how to fix the P0341 CHEVROLET code?
What does the camshaft position sensor on a Chevy do?
P0342 CHEVROLET Meaning The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module( ECM ) to control ignition and fuel injection.
When does the crankshaft position sensor become inoperative?
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals. Need more information on how to fix the P0342 CHEVROLET code?
How much does it cost to diagnose the p0341 Pontiac code?
The cost of diagnosing the P0341 PONTIAC code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0341 PONTIAC code detected?
How to test the cam sensor in GM 3.1L?
TEST 3: Making Sure The CMP Sensor Is Getting Ground. More GM 3.1L, 3.4L Test Articles. You can find this tutorial in Spanish here: Prueba: Sensor De La Posición Del Árbol De Levas (P0341) (at: autotecnico-online.com ). You don’t need any expensive tools to test the cam sensor on your 3.1L or 3.4L V6 engine. Multimeter.
What does the p0341 code on an engine mean?
What the P0341 code means. P0341 is an OBD-II generic code that says the engine control module (ECM) detected the engine camshaft position sensor circuit is not within specifications.
The cost of diagnosing the P0341 PONTIAC code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
On some Pontiac models the camshaft position sensor is part Ignition Control Module (ICM) (aka igniter). If playback doesn’t begin shortly, try restarting your device.