When did I start having problems with my Grand Am Se?
In June of 2008, at 79598 miles on the odometer, I began having trouble with my 2002 Pontiac Grand Am SE. The first thing I noticed as I was driving to work was that the “SECURITY”light was on. There did not seem to be any effect on driving, however, and I continued on to work.
Why does my Pontiac Grand Am Not Start?
On the 2002 Pontiac Grand Am, Olds Alero, and several other GM cars, the Ignition lock cylinder is the most likely cause of cars not starting because of security system malfunctions. Wear in the ignition cylinder causes the electronics within the security module to present a different signal to the yellow wire.
When did my Grand Am security light go on?
1999 – 2004 Pontiac Grand Am In June of 2008, at 79598 miles on the odometer, I began having trouble with my 2002 Pontiac Grand Am SE. The first thing I noticed as I was driving to work was that the “SECURITY”light was on. There did not seem to be any effect on driving, however, and I continued on to work.
Why is my PassLock not working on my Grand Am?
It turns out that although the most common culprit is a Security module in the ignition switch, there are several other possible causes for this Passlock problem. Anything which causes the apparent resistance in the circuit to change by a significant amount will trigger the security system, and cause the car not to start.
When does a Pontiac Grand Am out of gas?
(PRWEB) February 21, 2005 — If you own a 2001 Pontiac Grand Am, you’d better hope you’re not stuck somewhere bad when this hits: You go to start your car, and the engine cranks, but it seems like your out of gas, and won’t start.
What do I need to replace my 2002 Grand Am?
It is a 2002 grand am and so far I have had to replace the Catillic (not sure on the spelling) converter, master cylinder, fuel pump, gastic manifold, rack and pinon (spelling), hazard light switch (which still is clicking), and power steering pump. Also I need a new raditor.
Why does my Pontiac Grand Prix not start?
26 people found this helpful. When your car starts fine cold, then fails to restart while warm, it is usually a coolant system problem. Either low coolant, or bad coolant level sensor. 26 people found this helpful.
What is the ignition lock part number on a Pontiac Grand Am?
6/7/2011 Finally, the PREFERRED method of doing this modification Through the radio cavity, NO SOLDERING REQUIRED bergerweb.net/PasslockFix Note: 09/24/2010 The ignition lock part number is the same for all these cars: 1999 – 2004 Oldsmobile Alero 1997 – 2003 Chevrolet Malibu 1999 – 2004 Pontiac Grand Am
Is the Pontiac Grand Am a fleet car?
And as in 2005, the Grand AM SE Sedan was sold strictly as a fleet car, leaving only two coupe trims, the GT and GT1, available to the general public. For drivers, that meant 2006 Grand Ams could be had at good close-out prices and represented a good value.
When did the last Pontiac Grand Am Come Out?
The Pontiac Grand Am is a mid-size size (and later compact) car produced by Pontiac. The 1999-2005 generation is the final generation of the Pontiac Grand Am. Why is it when driving the RPM gauge drops or jumps up?
What is the SC / T package on a Pontiac Grand Am?
The SC/T Package added a power sunroof, a rear aero-wing spoiler, leather seats, and chrome wheels and exhaust tips. In addition, drivers noted that while interior storage space was limited and rear legroom could be cramped for tall adults, the Grand Am’s trunk offered plenty of cargo space, which could be expanded by folding down the rear seats.
How do you repair a PassLock on a Grand Am?
Separate the yellow wire from the bundle. Start the car, and while it is running, cut the yellow wire. Cut the yellow wire, and solder a switch inline so that the switch can be reached in an emergency. Place the switch in the closed position. Start the car, and then toggle the switch to the open position. Cut the yellow wire.
How to program a GM Pontiac GMC transponder key?
1. Insert the original, already programmed key in the ignition and start the engine. 2. After the engine has started, turn the key to off and remove the key. 3. Insert the key to be programmed and turn it to on within 10 seconds of removing the original key. 4. The security light will turn off once the key has been programmed.