How to do a Relearn on Passkey III?
To perform a relearn on a Passkey III system, make sure there is a fully charged battery in the vehicle. The battery will be used for 30 minutes without the alternator available for charging. Connect a battery charger to the battery to ensure power is available while programming.
When do I need to relearn the security key?
Start the If the vehicle starts and runs normally, the relearn is complete. If additional keys need to be relearned: Insert the next key to be Turn the key to the “ON” position within 10 seconds of removing the previously used key. Wait for security light to turn It should happen fairly quickly.
What should I do if my GM security light is flashing?
Insert ignition key and turn to the “ON” position. Do not attempt to start the engine. Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2.
How to reset PassLock 3 on a Chevy?
Passlock III reset procedure, reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Ricks Free Auto Repair Advice | Automotive Repair Tips and How-To
To perform a relearn on a Passkey III system, make sure there is a fully charged battery in the vehicle. The battery will be used for 30 minutes without the alternator available for charging. Connect a battery charger to the battery to ensure power is available while programming.
Start the If the vehicle starts and runs normally, the relearn is complete. If additional keys need to be relearned: Insert the next key to be Turn the key to the “ON” position within 10 seconds of removing the previously used key. Wait for security light to turn It should happen fairly quickly.
How do you reset the TPMs on a Pontiac?
Using the keyless entry (key fob), press and hold the lock and the unlock buttons simultaneously until the horn sounds. Starting with the LF tire, use a properly formatted TPMS scan tool to scan each sensor in the following order: LF, RF, RR and LR.
How to relearn the pass lock sensor code?
The vehicle is now ready to relearn the Pass lock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. Turn OFF the ignition, and wait 5 seconds.
What do you call a 10 minute ignition switch relearn procedure?
When doing this procedure, the BCM is actually doing the learning. So some people might call it a “BCM 10 minute relearn procedure”. Tip #2. If you want to do pinpoint testing using a voltmeter, you will need to get a wiring diagram from alldataDIY . They also have the removal and replacement procedure for the ignition switch if you need it.
How do you reset passkey on Saturn Ion?
Resetting the PASSKEY can be necessary at times if the programming in the module becomes corrupted or if a new key and key cylinder are installed. To reset the system, get in the car and shut the door. Turn the key on to the “Run” position without cranking the engine. Leave the key there for exactly 10 minutes.
How do you turn off the engine on a Saturn Ion?
Turn the key to the off position without removing it and back to “Run” for 10 more minutes. Turn the key off again and back to “Run” for 10 minutes a third. Turn the key off and then attempt to start the engine.
What’s the throttle body relearn procedure for a Saturn?
Start engine and ensure the engine speed is between 450 to 4,000 RPM. 2. Check that manifold absolute pressure (MAP) is greater than 5 kPa. 3. Check that the mass air flow (MAF) is reading is greater than 2 g/s. 4. Check that the ignition 1 voltage is greater than 10 volts. 5. Idle the engine in PARK for 3 minutes. 6.
How does the security system work on a Saturn Ion?
The Ion uses a passive alarm system that arm when you exit the vehicle and lock the doors with the keyless remote. If at any time the doors are opened without the use of the remote or the keys the alarm will sound. This is to prevent the theft of contents within the car.