How to fix a Pontiac Grand Am PassLock sensor?
Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks. I continuously have to wait until the light stops blinking….
When do you need to clear an error code on a Pontiac?
No matter what kind of Pontiac vehicle you drive, at some point you’re sure to come across a situation where the check engine light goes on and will require the error code to be cleared out. Error codes are triggered when your Pontiac’s computer detects a mechanical issue with the car and then illuminates the check engine light.
What to do when your Pontiac Grand Am won’t start?
To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset. Then I turn the key off and then back to start. It works every time but the 12 minute wait is a pain in the ass.
Why are my Pontiac Grand Am security lights not turning off?
The theft deterrent is disabling the starting of the vehicle because you have a problem with it. Your vehicle has what’s called ‘Passlock’. There is a sensor inside the ignition cylinder that has an electronic password. And i had read that if it is the ignition then the lights would not turn off.
How to bypass the PassLock sensor on a 2002 Pontiac Grand Am?
This web page will guide you through the steps necessary to bypass the “Passlock Sensor” on a 2002 Pontiac Grand Am, and keep the “SECURITY” light off forever. The steps necessary are similar on the other models listed above. There are generally only minor differences in how to get the radio out to get to the wires.
No matter what kind of Pontiac vehicle you drive, at some point you’re sure to come across a situation where the check engine light goes on and will require the error code to be cleared out. Error codes are triggered when your Pontiac’s computer detects a mechanical issue with the car and then illuminates the check engine light.
How to reset PassLock 3 security system on Chevy?
But here are some more articles to help Passlock III reset procedure, reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Passkey III Reset procedure. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time.
How long does it take to reset PassLock 3?
Passlock III reset procedure, reset security system on chevy, buick, oldsmobile, cadillac, pontiac, saturn, hummer. Passkey III Reset procedure. Make sure the battery if fully charged because this procedure may take up to 30 minutes and you cannot start the vehicle during this time.
What to do if power door lock does not work?
Put the key in the lock to unlock the door and the key turn 360. Will not not unlock the door. Have to unlock from the inside once get in from the other side. Have to pull up the door lock.
What causes a locked steering wheel to not turn in?
If a locked steering wheel is the only thing preventing your key from turning the ignition, then follow our instructions below for How to Unlock a Locked Steering wheel and you will be back on the road fast. Problem 2. Dirt, pocket lint or debris (like tape from opening a package) may cause your key not to turn in your ignition lock cylinder.
Can You disable the PassLock on a GM car?
The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.
Where is the ignition switch on a GM PassLock?
Pull the radio out of it’s cavity. Disconnect the wiring connector and the antenna wire, and set the radio aside. On the left side of the radio cavity, there will be an opening, through which you will be able to see the Ignition Switch.
Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks. I continuously have to wait until the light stops blinking….
Why does my Pontiac Grand Am Not Start?
Security system has been malfunctioning for a few years. When security light is on solid all the time, the car starts every time. That is because the security system is disabled. Only when the security system is enabled, security light off, the car has starting issues. Best way to fix is to permanently disable/disconnect passlock system.
Pull the radio out of it’s cavity. Disconnect the wiring connector and the antenna wire, and set the radio aside. On the left side of the radio cavity, there will be an opening, through which you will be able to see the Ignition Switch.
What to do if your PassLock sensor won’t work?
Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks.
The theft deterrent is disabling the starting of the vehicle because you have a problem with it. Your vehicle has what’s called ‘Passlock’. There is a sensor inside the ignition cylinder that has an electronic password. And i had read that if it is the ignition then the lights would not turn off.
Why does my 2003 Grand Am Not Start?
My 2003 Grand Am sometimes wont start. I’ve noticed that when it wont start, the security light is flashing. To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset.
How long does it take to turn off a GM security light?
Leave the key in the “ON” position for approximately 11 minutes. The security light will be steady on or flashing for the 11-minute period. Do not proceed to Step 2 until the security light turns off or stops flashing. 2. Turn the ignition switch to the “OFF” position for 30 seconds. 3.
What is the ignition lock part number on a Pontiac Grand Am?
6/7/2011 Finally, the PREFERRED method of doing this modification Through the radio cavity, NO SOLDERING REQUIRED bergerweb.net/PasslockFix Note: 09/24/2010 The ignition lock part number is the same for all these cars: 1999 – 2004 Oldsmobile Alero 1997 – 2003 Chevrolet Malibu 1999 – 2004 Pontiac Grand Am
6/7/2011 Finally, the PREFERRED method of doing this modification Through the radio cavity, NO SOLDERING REQUIRED bergerweb.net/PasslockFix Note: 09/24/2010 The ignition lock part number is the same for all these cars: 1999 – 2004 Oldsmobile Alero 1997 – 2003 Chevrolet Malibu 1999 – 2004 Pontiac Grand Am
To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset. Then I turn the key off and then back to start. It works every time but the 12 minute wait is a pain in the ass.
Why does my PassLock not work on my car?
The following information can help to determine the cause of the problem. The PASSLock system does not disable the starter; it only disables the fuel after the engine has started. If the vehicle will not crank, PASSLock cannot cause this condition. If the vehicle starts, but stalls quickly, this condition can possibly be related to PASSLock.
Why did General Motors start the PassLock system?
Aug 1st, 2005 The PassLock system was designed to prevent vehicle theft by disabling fuel to the engine if attempts are made to start the vehicle without the correct bitted key. PASSLock increased the level of security while retaining the ease of service and costs offered by standard ignition lock systems.
When did my Grand Am security light go on?
1999 – 2004 Pontiac Grand Am In June of 2008, at 79598 miles on the odometer, I began having trouble with my 2002 Pontiac Grand Am SE. The first thing I noticed as I was driving to work was that the “SECURITY”light was on. There did not seem to be any effect on driving, however, and I continued on to work.
Best way to fix is to permanently disable/disconnect passlock system. Not fixed, security light comes on solid and goes away in different time intervals while driving, then after a couple of starts it goes in that limp mode where the security light blinks.
Security system has been malfunctioning for a few years. When security light is on solid all the time, the car starts every time. That is because the security system is disabled. Only when the security system is enabled, security light off, the car has starting issues. Best way to fix is to permanently disable/disconnect passlock system.
The following instructions will allow you to disable the PassLock security in quite a few GM Vehicles. •This will allow you to install a remote starter and not have to purchase a bypass. •Avoid Costly repairs for an already broken PassLock System.
How to replace GM PassLock ignition key lock cylinder?
Press the small release tab (see pictures) While turning key to the ON Position Installation is the reverse of the above procedures, see below for the relearn procedure Clear all Diagnostic Trouble Codes (DTC). Record and/or repair your DTCs before clearing. You can clear the codes by disconnecting the battery for 10 minutes.
Why does my 1997 Pontiac Grand Am Not turn off?
This 1997 Pontiac Grand Am came in with the complaint that the ignition switch will not turn all of the way off. This causes two other problems. The key cannot be removed from the ignition lock cylinder and the ignition stays on enough for the systems not to shut down fully. The battery will go dead as a result.
How much does it cost to fix a no start Pontiac Grand Am?
Our technicians tell us that the ignition lock cylinder should be replace to correct this condition. The average cost for a Pontiac Grand Am No Start Diagnosis is between $88 -$111. Learn More Good news! We found 32 RepairPal Certified shops near you.
This 1997 Pontiac Grand Am came in with the complaint that the ignition switch will not turn all of the way off. This causes two other problems. The key cannot be removed from the ignition lock cylinder and the ignition stays on enough for the systems not to shut down fully. The battery will go dead as a result.
Our technicians tell us that the ignition lock cylinder should be replace to correct this condition. The average cost for a Pontiac Grand Am No Start Diagnosis is between $88 -$111. Learn More Good news! We found 32 RepairPal Certified shops near you.
What are the problems with the GM PassLock system?
If you decide to bypass your Passlock system, please contact us with the outcome so that we can pass the information along. By far, the most common problem with the VATS system is broken wires in the steering column. These wires connect the ignition lock cylinder to the under-dash wire harness.
Can a PassLock cause a car not to crank?
If the vehicle will not crank, PASSLock cannot cause this condition. If the vehicle starts, but stalls quickly, this condition can possibly be related to PASSLock. Most PASSLock-equipped vehicles have a telltale indicator in the instrument panel.
What do I need to replace my 2002 Grand Am?
It is a 2002 grand am and so far I have had to replace the Catillic (not sure on the spelling) converter, master cylinder, fuel pump, gastic manifold, rack and pinon (spelling), hazard light switch (which still is clicking), and power steering pump. Also I need a new raditor.
My 2003 Grand Am sometimes wont start. I’ve noticed that when it wont start, the security light is flashing. To resolve the problem I have to leave the key in the ignition with it in the “ON” position for 12 minutes to reset the sensor. The sensor light wiull stop flashing when it is reset.
How do you replace a Pontiac Grand Am security light?
Remove the cylinder from the ignition switch and replace with a new cylinder and Passlock housing….after replacement you will need to do a theft re-learn. To know exactly, you’d need a proper scanner to access the body control module and check for theft system codes.
On the 2002 Pontiac Grand Am, Olds Alero, and several other GM cars, the Ignition lock cylinder is the most likely cause of cars not starting because of security system malfunctions. Wear in the ignition cylinder causes the electronics within the security module to present a different signal to the yellow wire.
It is a 2002 grand am and so far I have had to replace the Catillic (not sure on the spelling) converter, master cylinder, fuel pump, gastic manifold, rack and pinon (spelling), hazard light switch (which still is clicking), and power steering pump. Also I need a new raditor.
How to repair a Grand Am PassLock security system?
Shake the unit and listen for water inside. If there is no problem with the Body Control Module, slide it back in place, making sure it is secure in it’s mount. Inspect the three connectors on the wiring harness to make sure all contacts are clean and not corroded.
What happens if you uninstall a car alarm circuit?
As long as this point of the circuit is held at the ground potential everything remains normal. However, if a burglar tries to uninstall the system and detaches the bolt, the circuit fires and sounds the car horn alarming everybody around, and you of a possible theft.
How many years are there on a Pontiac alarm?
Please scroll down as some years are combined! (ex: 2010-17) (displaying 1 – 40 of 128 records found by year descending, make, and model, click +/- to sort. Links to forum posts will appear in a new window.)
When to look for a failed circuit alarm?
If you are looking an instant notification the millisecond there is a power cut, then this device is for you. If you have unreliable power and don’t want it to nag you for brown outs but do want to know if there is a long term outage, look for something else.
Is the circuit alarm good in the garage?
The alarm is loud enough in our main level garage not to be missed on the main level of the house. Easy to install, test and figure out. Pretty simple, actually, and the piggy back plug is a good feature. If I were to suggest an improvement it would be to assemble without screws into plastic.
How to permanently disable and remove GM security systems?
GM Security Systems are killing cars all over North America and the only final solution is to disable and remove them permanently. This is what NEWROCKIES Inc is all about.
Is the circuit alarm on Amazon a good product?
Overall, great product for the money. Accomplished the goal, 1 caveat. Accomplished the goal. It’s a simple device that works great and does not drain the battery unless it’s in alarm. I would have given it 5 stars, but it trips instantly, even for brown outs.
How do you secure a PassLock sensor on a car?
Push the stripped end of the black wire into one of the empty holes of the terminal block of your Dummy Passlock Sensor. (see photo above) Tighten the screw to secure it in place. Push the stripped end of the yellow wire into the other terminal of your Dummy Passlock Sensor (see photo) and tighten the screw to secure it in place.
How long does it take to turn off PassLock sensor?
Observe the SECURITY telltale, after approximately 10 minutes the telltale will turn OFF The vehicle learns the Passlock™ Sensor Data Code and/or password on the next ignition switch transition from OFF to Crank. You must turn the ignition OFF before attempting to start the vehicle.