Why is my Navi CD not working properly?

Make sure the Navi disk itself isn’t damaged. If your stereo has only one slot for the Navigation DVD and audio CD, try inserting an audio CD or DVD to see it that works properly. If it does then the problem may be your disk and not the optical lens.

What to do if your Navi button is not working?

Press NAVI button and wait for the system to restart. If that doesn’t work go to the next step. Try resetting the COMAND system by removing the fuse for 15 minutes. Reinsert the fuses and check if the error message is gone. Check all the cables and connections in the back of the COMAND or the DVD drive.

What does it mean when it says ” Please check your disc “?

Once you get this error where it says “Downloading Software” and then, “Please Check your Disc”, it’s not a good sign. It means that either the DVD Rom Navigation is failing, or you have a scratched disc.

Why is my navigation not working on my Mercedes medic?

Reinsert the fuses and check if the error message is gone. Check all the cables and connections in the back of the COMAND or the DVD drive. Especially if work was done near those units. It is possible that one of the cables in the back of the unit has gotten loose or is disconnected.

When does an error message appear in Navisworks?

“An error was detected when attempting to page data in from disk…” appears when accessing a file in Navisworks disk. You are advised to restart the application. Navisworks fails to load some data from the file disk.

Why is my navigation system not working properly?

Navigation system is unable to acquire a proper GPS signal. Navigation unit door is open or No DVD Disc installed. Please check system. PC card slot door is open. Please check system. No DVD Disc, please check system. Display temp is too high. System will shut down until display cools down.

What to do if your navigation disc is damaged?

Your navigation disc may be damaged. Remove it from the tray in the trunk and check for scratches. It may have to be replaced. 34 people found this helpful. ok, checked for scratches but don’t see any. should the cd remain in or should it be taken out or it should remain in the cd drive at all times? 13 people found this helpful.

It is possible that one of the cables in the back of the unit has gotten loose or is disconnected. Another common error message that you will see is “Navigation is initiating please wait” Under such conditions the COMAND system works correctly except the navigation system. Here are a few possible causes and solutions to this problem.

Why does my navigation DVD say ” cannot read “?

A related error is: “Cannot read navigation DVD” which is displayed when old navigation DVD is severely scratched or damaged. Make sure you are also using a compatible DVD disk. You may also get messages such “ Navigation is initiating, Please wait ” This can be caused by a dirty optical laser eye / optical head or lens.

If the system still can not locate it, it is most likely that the map in the system will need to be updated. Map does not appears on the monitor. It is possibly that the scale of the navigation map is either too small or too large. Try to change the scale of the map, you should be able to see the navigation map on the monitor now.

Why is the touch screen on my GPS not working?

Touch panel is not calibrated. Press “calibration” to calibrate the monitor again. No response from the touch screen. If there is still no response after a long period time, please contact the after-sale service department to have this issue looked at. Can not play DVD. Disc loaded inaccurately.

What to do if your GPS is not turning on?

If your GPS is not turning on or starting up, use the following steps to check and make sure the GPS has power: Turn the vehicle key to ACC or IGNITION position. Connect the power cable to the GPS navigation unit if it is a stand-alone unit. Check the fuses in the fuse panel. It’s normally on the driver-side of your car. Replace any blown fuses.

Why does my navigation map not show up on my monitor?

Map does not appears on the monitor. It is possibly that the scale of the navigation map is either too small or too large. Try to change the scale of the map, you should be able to see the navigation map on the monitor now.

Why is my navigation DVD not loading on my stereo?

If your stereo has only one slot for the Navigation DVD and audio CD, try inserting an audio CD or DVD to see it that works properly. If it does then the problem may be your disk and not the optical lens. If you are trying to update the navigation system using an update DVD you may get an error message saying Loading Navigation.

Why is my voice navigation not working on my iPhone?

Make sure your iPhone isn’t on Silent mode, which can automatically mute voice navigations. Flick the switch above your volume buttons so you can’t see any orange. An alert should appear on your iPhone saying Silent mode is off. Then go to Settings > Sounds & Haptics.

What does it mean when it says navigation cannot be activated?

Error message “Navigation CanNot be Activated” usually means that the Navigation system is not being able to start up (boot up) which could be due to several reasons. Common problems include wrong DVD disk, issues with the navigation processor A40/3n2 or fault in CAN bus (controller area network) communication.

Why is my car radio display not working?

Your car radio may have damaged connectors that are not able to transmit power and information to the display LED, and it is not able to work. There can be several possible reasons that can cause the connectors of the LED to stop giving power. The main reason for the damaged connectors can be a loose connection of wires of the connectors.

How to troubleshoot a GPS navigation unit in a car?

1 Turn the vehicle key to ACC or IGNITION position. 2 Connect the power cable to the GPS navigation unit if it is a stand-alone unit. 3 Check the fuses in the fuse panel. It’s normally on the driver-side of your car. Replace any blown fuses. 4 Make sure the battery is fully charged if it has a battery.

What to do if the radio programming software does not?

Note the new COM Port number assigned to the USB Programming Cable and go back to Step 3. If a new COM Port number was assigned to the cable and it is still not recognized by your programming software, skip to Step 6. Step 5. Run or close and restart the programming software. Step 6.

Why is the CD not working on my RNS-E?

You may be lucky and find that it just had issues with that particular disc and may work correctly with a navigation disc once you remove the stuck CD. Personally, I wouldn’t bother with CD’s in an RNS-E – just leave the Navigation DVD in and use an SD card for music.

Why is the eject button not working on my A3?

The eject button is disabled at the factory during assembly. It’s to prevent the nav dvd being stolen during delivery. A3 2.0TDI Sportback S Line 184 Quattro S-Tronic, Mar. 2014 Glacier white.

Why is my CD not working on my Toyota?

Common Problem: Touch panel not responding , Black display ( no back light ) , CD does not play , GPS does not work , Won’t accept CD , Won’t eject CD, Error message . Note: Remove your discs from CD Changer prior shipping .

Why is my Mercedes navigation not working properly?

All the units which are part of the fiber optic need to be in proper working condition. If your Mercedes uses a separate drive for the NAVI DVD, it is possible that this unit can be defective. Learn more about fiber optic problem by reading Mercedes Audio System Explained. The DVD drive that holds your navigation disk could be damaged.

Can a navigation card be replaced if the VIN is not correct?

When a Navigation SD card has been separated from its VIN-bound vehicle and the correct vehicle is unknown, the only solution is to replace the card. The new vehicle warranty does not cover Navigation SD cards replaced for an incorrect VIN. If the VIN on the card does not match the warranty claim submission, it can be subject to debit.

What to do if your Nav screen won’t open?

CAUTION: disconnecting the battery cable will reset the NAV, Radio and Hybrid systems (s). Do this at your own risk. Once reconnected – the nav screen “open” button worked and I was able to remove and re-insert the NAV disc. This solved my problem, but I had to re-enter my saved addresse and radio settings. HH Limited.

What should I do if my navigation system is not working?

But electronics by any company, no matter their reputation, can run into problems. Sometimes the issue can be easily resolved by simply unplugging the navigation system’s computer. Knowing how to reset your navigation system can save owners a costly repair bill.

What to do when map disc won’t open?

Hold the disc still until the touchscreen changes to say that the disc is invalid and to contact your dealer. After that hit the eject button again which will close the screen then hit te eject button and touch the eject map disc button. After doing this the disc SHOULD eject.

Why do I get a map disc read error?

A few months ago, I started getting this ‘MAP DISC READ ERROR’ notice on the screen, and I could hear the map disc spinning behind the radio touch screen. The nagivation stopped working.