Why is my odometer and speedometer not working?

Odometer & speedometer not working ABS & Brake warning lights lit. I have the same problem! what number fuse is it? and where is it located ? 756 people found this helpful.

Where are the fuses for the dashboard lights?

Check under the hood, under the dashboard, or near or in the glove compartment. Once you find the fuse box or boxes, remove the lid and check the diagram on the underside of the lid for a fuse labeled “dash lights” or just “lights.” Refer to your owner’s manual if you have trouble locating the fuse boxes or the dashboard light fuse.

How can i dim the lights on my dashboard?

Put the key in the ignition and turn it to the “on” or “accessory” position. Then, turn on your headlights. Locate the dimmer switch for your lights. Most vehicles have a dashboard light control switch that will dim the dashboard lights as well as turn them off.

Where is the dimmer switch on the dashboard?

Locate the dimmer switch for your lights. Most vehicles have a dashboard light control switch that will dim the dashboard lights as well as turn them off. Find the control switch, dial, or knob, which is generally located on the console near the steering column or may be part of the headlight switch.

Why do I have a buzzing headlight alarm?

On the way home there was a bit of fog but otherwise daylight. Turned on the lights for safety. Arriving home we unloaded, cleaned up and left the lights on to fully drain the battery – just for good measure. Sooooo, after a new battery and day of kicking my own posterior I went online to try and find a 3rd party headlight alarm.

Where does the middle pin on a headlight go?

The middle right pin connects to either the closed or open pin, depending upon if voltage is applied to the coil pins. Instead of trying to splice wires I opted for, in my opinion, a slightly better and less prone to fault option.

What to do when both head lights stop working at the same time?

When that happens, the operational lifespan of your headlight capsule will be severely compromised, and the only fix is to replace the headlight assembly. When both headlights stop working at the same time, the bulbs usually aren’t at fault.

Why are my headlights not working in high beam?

If just one bulb fails to work in either high beam mode or low beam mode, it may be the bulb. Most headlight failures that are limited to just high or low beams are related to a relay or the high beam control switch.

The speedomerter, odometer & mileage guages are not working. Have not experienced any other symptoms. Brakes are operating properly, have not received any warning/service lights other than tires need rotating. Was told by a mechanic that it’s the ABS System Sensor and was given the quote for a used one for $500 plus. Can you advise on this?

Why does my Odo stop working on my tripmeter?

If the speedometer is still working the problem is in most cases very simple: inside the instruments unit there is a very small cogwheel which is made of nylon. Sooner or later a small tooth (or even several teeth) will break and the tripmeter will stop working, resulting the odometer to stop working.

Can a broken speedometer lead to a ticket?

You should diagnose and resolve the problem as soon as you see it, since not knowing how fast you are going can lead to a ticket. Also, in most states you won’t be allowed to register a car with a broken speedometer. A faulty, damaged, or broken VSS can cause your speedometer to fluctuate and completely stop working.

Where is the speedometer and odometer located?

If both your odometer and speedometer are not working, then it’s likely your speed sensor needs to be replaced. These are easily installed and located near the back of your transmission.

Why does the trip odometer not reset to all zeroes?

The trip odometer is ordinarily reset to all zeroes with the button, and will accumulate trip mileage until it is reset again. Over years of usage and mileage accumulation, a fault develops where the trip odometer to fail to reset to all zeroes. This is a common problem with higher mileage cars.

How do you replace a speedometer on a Honda?

Undo several clips on both sides of the dashboard bezel, and remove it. Use a 1/4” ratchet, socket and extension to remove the wiring cluster from the dashboard. Unplug the harness from the gauge cluster. Plug the stock harness into the replacement gauge cluster/speedometer. Use the 1/4” ratchet, socket and extension to install the new cluster.

Is there a way to reset the odometer?

There is no way you can reset the mileage shown by the odometer, through this repair procedure or any other. So you don’t need to worry about causing an accidental resetting. This repair job is very delicate work and you need to be very careful, while removing all connected parts and reassembling them together.

Why is my odometer not registering a mile?

It causes the input shaft to make 1690 rotations, to register a mile. Considering that the reason for odometer problems is the wearing out of the planetary gear (which is the most common reason), I present the overview of a general repair procedure, involving its replacement.

What to do if your odometer and speedometer are not working?

The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix. If both your odometer and speedometer are not working, then it’s likely your speed sensor needs to be replaced. These are easily installed and located near the back of your transmission.

If both your odometer and speedometer are not working, then it’s likely your speed sensor needs to be replaced. These are easily installed and located near the back of your transmission.

Why does the odometer on my Car Stop Spinning?

But the plastic gears that turn an analog odometer have a tendency to break, which causes the odometer to stop spinning. The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix.

How do you find the ignition relay on a car?

When you locate the fuse box, open it and find the mapping on top of its lid. The key will tell you the exact position of the ignition relay as well as other relays and fuses. Once you have located the relay, gently pull on it to remove it from the fuse box. The relay looks like a rectangular block and is hard to miss.

What are the symptoms of a bad ignition relay?

Fortunately, a number of symptoms can tell you beforehand if there is a problem waiting to happen or if it has already happened. We will now look into the signs of a failing ignition relay in detail. 1. Ignition is Unresponsive The ignition relay’s primary job is to help you start the car.

What does it mean when your abs light comes on?

Most commonly, this light is triggered by low brake fluid or an engaged parking brake. However on some vehicles, it can simply indicate a problem elsewhere in the system and can be illuminated immediately if there is an ABS fault.

Can a parking brake light be activated by ABS?

Usually, the brake fluid level sensor and the parking brake are the only two items that can activate the BRAKE light. But, not all vehicles are the same, and some of the earliest ABS systems would trigger both lights simultaneously for any ABS fault.

When did the Speedo stop working on my Dodge Ram?

53 people found this helpful. I have a 2001 Dodge Ram 3500 Van and about 9 months ago the speedo stopped working, the AC stopped working (blowing cold and vent blowing on HIGH), the ABS and Brake light came on steady and the check engine light came on. It also pulsed or surged at times when driving.

Is the speedometer not working and ABS and brake light stay?

Re: Speedometer not working and abs and brake light stay… You can’t post conmments that contain an email address. An expert who has achieved level 1. An expert whose answer got voted for 2 times. Re: Speedometer not working and abs and brake light stay…

Why is my abs and brake light not working?

If you purchase one from a junk yard or used parts dealer, your mileage will not be correct and some of your options will not work. You can’t post conmments that contain an email address. An expert who has achieved level 1. An expert that has 1 follower. Re: Speedometer not working and abs and brake light stay…

Why is my speedometer not working on my Dodge?

My company used to repair body computers (BCM) for Chrysler/Dodge vehicles which contol the warnings you are getting. The car wash could be a major clue. We have seen numerous false intermittent warnings created due to fluid intrusion, such as water, into the BCM assembly.

What to do when your brake light stops working?

My cruise also stopped working, and I noticed my brake lights would stay lit anywhere from 2 to 10 seconds after lifting my foot off the brakes. I simply replaced the brake pedal switch located just above the brake pedal. ($10) Took about 2 minutes if that. Please rate and respond to both of my posts if this helps anyone else.

Why is my Jeep Liberty on the passenger side?

The contact owns a 2008 Jeep Liberty. On several occasions, the passenger side door lock failed to lock and unlock as intended. The contact stated that the vehicle was driven on the passenger side because it was used as for postal deliveries.

Why is my odometer not working on my Dodge Ram 1500?

My speedo was possessed, fluctuating while parked and the odometer was advancing, also while parked. The ABS, Check engine, and Brake lights were all on. I first bought a new CPU. wasn’t the problem and took it back, tried a new Gauge cluster from a friends truck, still nothing.

How is the ABS light different from the brake light?

The ABS light differs from the BRAKE light as it is usually controlled by a computer module. When this light is on, there are often trouble codes stored to help the owner or a technician diagnose the source of the fault in the anti-lock braking system. The BRAKE light on most vehicles is activated by…

How does the ABS module affect the brake pads?

The ABS module or in some models the SBC Brake module will apply pressure to the brake pads at each of the individual wheels depending on the directions it receives from the vehicle’s control units. While it is less likely to fail, it is known to be a problem as well. Replacing the ABS Module can be costly.

When do you turn off the ABS light?

After the broken ABS (Anti-lock Braking System) has been fixed and work properly again, the light will go off. How to turn off the ABS light is actually to get the Anti-lock Braking System fixed. 2. Can You Drive With An ABS Light On?

How can I tell if my brake pads are wearing down?

When the brake pads wear down to a certain point, typically around 15 percent material remaining, the pads contact the sensor and the light illuminates. Step 1: Check for a Brake Pad Warning Light. If your car has this special brake pad sensor, you will see this symbol illuminated on your dashboard if your brake pads material has worn down.

What does it mean when your brake system light is on?

The brake system light indicates a much bigger issue with your braking system — a problem which may limit your ability to brake the vehicle at all. Therefore, you would need your vehicle towed to the mechanic if you notice both lights on.

What does it mean when your temperature gauge is not working?

The temperature sensor/sending unit is faulty. If this is the case your sensor will be reading the coolant temperature incorrectly and sending the wrong signal to the gauge. This could work in either direction and read as cool when it’s running hot or hot when it’s running cool. A malfunctioning circuit in the temperature gauge

What should I do if my gas gauge is not working?

Note that some self-test steps may stop the gas gauge at 1/4, 1/2, and 3/4, as well. Fuel sender test. The fuel sender test should be conducted when the tank is lower than HALF, to prevent fuel splashing. Start by making sure the plug is clean, dry, and free of corrosion. Make sure the pins are straight and that the connector is fully seated.

Why does my gas gauge keep pegging full?

The gas gauge might interpret voltage feedback from a dead sender as FULL or EMPTY, consequently pegging the gauge no matter the actual fuel level. Circuit Problems can cause the gas gauge to stop functioning normally.

How is the gas gauge in the instrument cluster?

The gas gauge in the instrument cluster is the visual indication of activity in the fuel tank and sending unit. Some gas gauges are directly controlled by voltage feedback from the sending unit, while others are controlled by the instrument cluster, which itself gets voltage information from the sending unit.

Can a replacement odometer show the original mileage?

The odometer replacement sticker will have the original mileage hand written on it from the tech who replaced the meter. The repair order will also have the original mileage and date on it, the repair order is a legal document, and it is proof of original mileage. The new odometer will start clocking mileage from that point starting at zero miles.

Why do I have to send my odometer to the metering shop?

The reason for sending both new and old odometers to the metering shop is because the mileage of the vehicle cannot change while the new odometer is being synced. If the instrument cluster is removed from the vehicle, it’s to be expected that the vehicle will not be driven.

When to suspect odometer has been tampered with?

So if you happen to see gouge marks around the instrument cluster, be sure to ask if the odometer has ever been changed out, don’t assume the odometer mileage has been tampered with because there are many reasons to remove the instrument cluster, and not just to get to the odometer.

How does the speedometer work in a car?

The speedometer determines the vehicle’s speed by drawing information from the transmission and driveshaft. The ECU (engine control unit) converts the driveshaft’s rotation speed to the vehicle’s linear speed and then passes the information to the speedometer.

How do you remove speedometer from dashboard?

Gently remove the entire speedometer gauge assembly, out of the dashboard. You need to be slow in doing this, taking care to not disconnect the wires connected to the gauge, from behind. Look at the back side of the gauge and observe the wire connections made to it. Take a snapshot, if you want, before you go ahead and remove the wire connections.

What should I do if my speedometer is not working?

Troubleshooting speedometer problems mostly call for a replacement of the speed sensor or cable, depending upon the vehicle. Both these repair jobs are simple to perform and can be done at home.

How does the speedometer and odometer work?

This is likely related to what is called a speed input/output shaft sensor which is a sensor mounted down on the transmission that monitors the speed of the output shaft of the transmission. This is relayed to your ECU which produces this information in your speedometer and odometer.

Why does my speedometer keep bouncing between speeds?

Bouncing or jerking of speedometer In cases where the speedometer does not settle on any particular reading but keeps moving between speeds, it is almost always due to bad wiring, in case of a cable system, or a faulty speed sensor. In most cases, only the wiring needs to be changed, or the sensors re-calibrated, to repair the problem.

What happens when a speed sensor stops working?

A speed sensor does not only indicate the vehicle speed but also help with cruise control operation and regulation of the fuel’s flowing and ignition timing. A speedometer may stop working due to a bad sensor.

Is there a way to disable the brake light?

Not sure of a way around it beyond disabling the brake light function / removing the script. Turn Signals: If you have no controller modifier key for indicators and blackout for taillights is the same button as a turn signal, turn signal will not work.

What happens when you turn on the right turn signal?

Turn Signals: In an ELS Enabled vehicle, if you turn on the right turn signal and your ELS blackout bind is the same as the turn signal, it will activate ELS’ blackout mode. What’s New in Version 1.0.6

What to do if your speedometer is not working?

Speedometer not working… Speedometer lights up and does everything else but move the needle off of zero. I checked the connection under the instrument console, ran a diagnostic to find out that all codes are clear.

Why is the odometer on my Harley Davidson not working?

The odometer mileage is displayed but does not change. The trip meter stays the same and does not change. The directionals don’t self cancel any more. All codes clear. I recently installed an amp with speakers that runs off of an ipod.

Is it time for a new speed sensor?

Perhaps it is time for a new speed sensor? or is it time for a new speedo. 2000 softail deuce. Okay. I replaced the speed sensor ($58) from the dealer.

Why are the lights on my dash not working?

Flip the switch or turn the dial or knob up and see if the lights on your dash come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb. Or, the entire switch may be faulty, in which case, have it replaced by a certified mechanic.

Why is the ABS light and brake light not working?

I have a 1998 Dodge Ram 1500 Both the ABS light and the brake light are on. Changed the Speed sensor on the differential it didn’t help. I did replace the RWAL/ABS fuse and now the speedo works. Next I’m checking the front wheel sensors after that idk what to try. Any advise would be helpful. I have a 99′ Dodge RAM 2500.

Odometer & speedometer not working ABS & Brake warning lights lit. I have the same problem! what number fuse is it? and where is it located ? 756 people found this helpful.

What to do if your dash light does not work?

#Test the dashboard light bulbs. If the fuses are working properly, check for a blown bulb in the dashboard. Following the manufacturer’s instructions, disconnect the battery while working on the dash, remove the faceplate covering your vehicle’s dashboard gauge panel. Remove the screws holding the plate on. Carefully remove the faceplate.

Where is the control switch for the dashboard lights?

Most vehicles have a dashboard lights control switch that will dim the dashboard lights, as well as turn them off. Check the control switch, which should be located on the console near the steering column or part of the headlight switch. [ [Image:Fix Dashboard Lights That Won’t Light Step 1 Version 3.jpg|center]]

What happens if the speed sensor does not work?

If this speed sensor fails, your speedometer may not work. Some odometers use the same sensor as the speedometer, and may cease to function as well. Without a speed sensor, the transmission control unit (TCU) may have a hard time knowing when or how quickly to shift gears.

Can a check engine light be a bad speed sensor?

But if you have malfunctioning cruise control and a Check Engine light coming on, this is a clear indication of a faulty speed sensor. After all, the engine control unit depends on having valid speed information regarding the engine’s crankshaft.

How does an optical speed sensor work on a Miata?

An optical sensor uses light that shines through a spinning disk to determine speed. Like the Hall Effect sensor, an optical sensor also produces a square waveform. First generation 1.6L Miatas used an optical CAS sensor instead of a Hall Effect sensor. What is a Transmission Speed Sensor?

How does the odometer work on a Mazda 6?

The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the selector while one of them is displayed. The selected mode will be displayed. The odometer records the total distance the vehicle has been driven. The trip meter can record the total distance of two trips.

How does the trip odometer work on a Harley Davidson?

Easy reach with your left index finger and each press scrolls thru total miles, trip A, trip B, miles to empty, then back to total miles. At least by my memory and on my bike. Hope this helps. Sometimes its better to keep your mouth shut and be thought a fool than to open it and remove all doubt.

How can I change the mode of the trip meter?

The display mode can be changed from odometer to trip meter A to trip meter B and then back to odometer by pressing the selector while one of them is displayed. The selected mode will be displayed.

What happens to the odometer when you turn off the gas?

The car’s odometer cluster, including fuel guage, speedometer, rpm meter, temperature etc becomes dead sometime (while driving or when I begin driving) and when this is dead the car starts loosing accelerations beyond certain speed. If I push the gas pedal hard, nothing happens, it seems like the car has been turned off.

Why is the speed sensor on my Nissan not working?

It happens sometimes, usually when the car has been standing for the day in sunlight, and it goes away by itself. I took it to a dealer and dealer replaced Speed Sensor (CODE: P0500) – spent $250 on it already The issue hasn’t been fixed yet, the dealer says to bring the car when the issue is there.

What should I do if my odometer is broken?

You need to pull instrument cluster to get at those gears, but it’s not too bad to repair so long as you know what you’re doing. Since you’ve got your cluster out, make sure you remove any dust using compressed air and clean the clear plastic using a microfiber cloth.

Why is my fuel gauge not working on my Road Star?

No announcement yet. Hello all, I have a 2003 Road Star Silver edition I recently inherited from my uncle that passed. bike runs perfect but basically all the gauges for the exception of the light are not working and I cant find a fuse that may be the issue. can someone please help.

Can a fuel gauge work on a motorcycle?

Every one I have contacted said they do not work on motorcycle speedometers. My 2001 Roadstar Fuel Gauge also stuck recently and my speedometer needle also is lazy to work but then works after a few minutes and/or tapping on the gauge cover Haven’t taken the time to mess with it but maybe now I’ll get off my A** and clean the needle as mentioned.

How do you test the fuel sending unit?

To test the fuel sending unit, you will need to fill the tank with gas. Use a multimeter to test resistance. In an old-school classic with analog gauges, you’ll need to know how the gauge works, as manufacturers used different electrical conductance to operate the gauge.

When does the ABS warning light come on?

Anytime a problem occurs in the ABS brake system the warning light gets on. In fact, ABS light stays on unless you fix the core issue. Basically, the warning light alerts the driver that the safety system is no longer active.

What happens when your gas gauge is not working?

The gas gauge tells you how much fuel is in your gas tank and alerts you when it’s time to refuel. If your gas gauge is not working, the inaccurate information it provides may cause you to run out of gas unexpectedly.

How does a fuel pump work on a gas gauge?

The fuel pump module includes the fuel sending unit, used by the gas gauge to detect and display fuel level. https://www.flickr.com/photos/3ndymion/33556245572. The gas gauge is a relatively simple circuit, but its simplicity means each component is essential to its function.

What does a gas gauge tell you about a car?

Benjamin Jerew is an ASE-certified Master Automobile Technician with over a decade of experience in auto repair, maintenance, and diagnosis. The gas gauge tells you how much fuel is in your gas tank and alerts you when it’s time to refuel.

Navigation