What does it mean when a Peugeot 206 wont start?
I could give up Stella, but I’m no quitter. hi angus checked for ign voltage on plug 3 this morning and there was none, i have continuity tested wire back to fuse box and it is good. when i applied voltage on to pin i did get engine management light on , does this maybe mean that there is immobiliser fault? not sure what to try next.
Why is the crank sensor on my Peugeot 206 not working?
The crank sensor doesn’t have an ignition feed. You need another feed to plug 3 A4 – but you’ll only get that if the immobilizer is happy [?] the inertia switch isn’t tripped and the ECU commands it. How did this fault occur?
Is the scanner on my Peugeot 206 communicating with ECU?
Rob. hi rob thanks for your swift reply, yes the scanner i have does not communicate with ecu, not getting anything at all. will check wiring above gearbox, when you say tight do yo mean maybe wrong routed ?or is this a common prob with these. As to wiring; there are many different makes of ECU fitted on that year.
Where does the ignition feed come from on a Peugeot 206?
The coil; injectors and pump are all fed from the fuel-pump side of whichever you have and would only be fed briefly at key-on and when cranking. The crank sensor doesn’t have an ignition feed.
Is there a problem with my Peugeot 206?
Hi, I have a 2005 Peugeot 206, I’ve only been driving the car a few days, I’ve just tried to start it to go out and it’s turning over/ cranking but will not start, I’ve not had this problem with it before and the previous owner was my partners mother and neither has she, the car ideally starts straight away with no problem but now has just stopped.
The crank sensor doesn’t have an ignition feed. You need another feed to plug 3 A4 – but you’ll only get that if the immobilizer is happy [?] the inertia switch isn’t tripped and the ECU commands it. How did this fault occur?
Rob. hi rob thanks for your swift reply, yes the scanner i have does not communicate with ecu, not getting anything at all. will check wiring above gearbox, when you say tight do yo mean maybe wrong routed ?or is this a common prob with these. As to wiring; there are many different makes of ECU fitted on that year.
The coil; injectors and pump are all fed from the fuel-pump side of whichever you have and would only be fed briefly at key-on and when cranking. The crank sensor doesn’t have an ignition feed.
How can I tell if my Peugeot has a bad battery?
Then, if you notice that the light becomes much weaker, you need most likely charge the battery and try to start your Peugeot again. Also with the battery discharged and the key turned to start position you can observe that the wiper blades incidentally start operating and the dashboard blinks.
Why does my Peugeot 1007 won’t start?
Peugeot 1007. Left unused for 10 days, went to start it but it would only spin over then the battery went flat. Charged the battery and refitted but it … read more Proprieter / Diagnostic Tech… Proprieter / Diagnostic Tech… Proprieter / Diagnostic Tech… Proprieter / Diagnostic Tech… Proprieter / Diagnostic Tech…
Why does my Peugeot won’t start up?
My peugeot won’t start and not sure why. Eco mode is active – battery has been replace and the BSI reset. Could it be Peugeot repair questions? Ask a mechanic for answers ASAP
Why is my fuel pump not working on my Peugeot 306?
Other factors which could cause an engine to falter are a faulty EGR valve or fuel pump failure. What could be preventing a Peugeot 306 from starting or the fuel pump from being heard? Check fuse 35 which protects the fuel pump and also check that voltage is reaching the pump.
Why does my Peugeot 206 make a humming sound?
Will a defective Peugeot 206 fuel pump, which makes a humming sound, prevent the engine from starting? A humming sound could indicate a failing fuel pump. The pump generally hums for about 10 seconds after the ignition is switched on before the relay cuts it off.
Why is the fuel pump no spark on my 206?
There is no live at #4 pin of the coil pack and no fuel pump priming when ignition switched on. ECO mode is on the display. Have changed ECU (Sagem) & BSI + Key from a working 206 (matching numbers) but still the same problem. Central locking working from key and after trying to start it and switching off beeping when door open.
What kind of engine does a 206 estate have?
Got a 2004 (54 plate) 1.4 206 Estate car that has come to me as a non runner. Snap On Solus will not communicate with the engine ecu but does with abs system no problem. There is no live at #4 pin of the coil pack and no fuel pump priming when ignition switched on.
Why does my Peugeot 206 lock up after opening?
Check all the locks in the central locking system. These are prone to locking immediately after opening or opening straight after locking. It’s a common fault that’s caused by a broken actuator, which will require a quick replacement to make the vehicle secure once again.