How to replace the serpentine belt on a 2005-2016 Nissan?
Brian Eslick from How to Automotive http://www.howtoautomotive.com takes you step-by-step through the process of Replacing the serpentine belt on a 2005-2016 Nissan Xterra/Frontier with the 4.0L engine. Estimated repair time is .50 of a hour. You will need a 3/8 ratchet, 10 mm socket and a new belt. Check links below.
Where do I find the serpentine belt on my car?
To access the serpentine belt, you will need to open the hood of the vehicle. The hood release can usually be found near the door on the driver’s side of the vehicle. With the hood released, you will also need to release the safety latch located at the front of the vehicle.
What makes the belt squeak on a Nissan Frontier?
Well this article will show you how to fix your problem! The belt tensioner on the Nissan 4.0L V6 (VQ40) found in the Nissan Frontier (2005 and up), Pathfinder (2005-2011), and Xterra (2005 and up) does not properly tension the belt over time, which is what causes the annoying squeaking noise because the belt is slipping in cold/damp conditions.
What happens when you loosen a serpentine belt?
If your vehicle uses the alternator bracket to apply tension to the belt, loosen the two bolts that pass through the long eyelets on the bracket. As you loosen the bolts, the tension on the belt will likely move the alternator toward the engine and relieve the pressure. Loosen the bolts enough to move the alternator, but don’t remove them.
Brian Eslick from How to Automotive http://www.howtoautomotive.com takes you step-by-step through the process of Replacing the serpentine belt on a 2005-2016 Nissan Xterra/Frontier with the 4.0L engine. Estimated repair time is .50 of a hour. You will need a 3/8 ratchet, 10 mm socket and a new belt. Check links below.
Where is the belt tensioner on a Nissan Frontier?
I’ve included a picture of the belt routing diagram for the VQ40DE 4.0L V6 engine. The silver metal belt tensioner assembly is located near the center of the engine. To rotate the tensioner arm and release the old belt, you’ll need to use a 3/8″ drive ratcheting wrench.
How do you remove the serpentine belt on a pathfinder?
To remove, you simply pop off the two clips on the right side of the airbox, then lift up the right side of the lid and pull out. Set the air box to the side. Next you will need to remove the serpentine belt. This is where you will need the serpentine belt tool. You’ll attach the 3/8″ drive end of the tool into the slot on the belt tensioner.
What kind of belt tensioner do I need for Pathfinder?
1 Serpentine Belt Tool (I rented this serpentine belt tool from Advance Auto Parts for $35, then you can get a full refund upon return of the tool within 30 days). I tried to use a breaker bar and a ratchet instead, but there just isn’t enough room without removing the fan and fan shroud.
How do you change fan belt on Nissan Patrol?
How to Change the Belt on a Nissan Patrol Turbo Diesel Turn the engine off, allowing it enough time to cool. This will save you the trouble of receiving burns while working under the hood. Pop the hood of the car and locate the fan belt attached to the side of the engine. Loosen the nuts that create tension on the connecting pulleys.
How do you adjust the belt on a car?
Adjust the belt as needed to get a half-inch of tension in the belt. Tighten the bolt in the middle of the adjustment bracket and the top alternator mounting bolt with the ratchet and socket. Crank the engine for fifteen to twenty seconds. Turn the engine off and inspect the belts.
How is the serpentine belt on a car tightened?
The serpentine belt is a single belt with ribs on the inside of the belt that travel inside of the pulleys. The serpentine belt is tightened by a spring loaded tensioner on the front left hand side of the engine. Use the bolt head that secures the pulley to the bottom of the tensioner to relieve the tension from the belt.
What is the fan belt on a Nissan pickup?
The fan belt on the 1995 Nissan Pickup is a V-belt that also operates the alternator. The belt is driven around the fan pulley and the alternator pulley by the crankshaft while the engine runs.
How do you change the belt on a Nissan?
Tighten the lock bolt in the middle of the adjustment bracket tightly with the ratchet and socket. Inspect the belt and make sure that it is situated inside all three pulleys. Crank the Nissan for about 15 seconds to completely seat the new belt to all three pulleys. Turn off the engine and recheck the tension of the belt. Close the hood.
Where are the hoist brackets on a Datsun?
Attach an engine hoist capable of lifting up to 8-feet or higher to the two hoist brackets located on the engine. One is on the front near the idler pulley and the second is at the back of the engine behind the air cleaner assembly.
How to change the clutch on a Datsun 720?
Once the tabs are removed, the lower shroud pulls out easily. Then using a 10mm wrench or large phillips screwdriver, remove the 4 screws holding on the plastic portion of the fan shroud.
What kind of drive belt does a Nissan have?
About Nissan Drive Belt. As its name shows, drive belt drives some components in your engine, like water pump, power steering pump, alternator and air conditioner compressor. You may have one or two drive belt in your Nissan car. Although it is made of a strong rubber, it still can be worn one day.
When to take care of your Nissan drive belt?
Although it is made of a strong rubber, it still can be worn one day. Generally speaking, if you drive your Nissan more than three or five years, or 45,000 or 75,000 miles, then it is the chance for you to take care of your drive belt.
How do you remove a serpentine belt from a battery?
Use the appropriate sized wrench or socket to loosen the nut holding the black ground cable on the negative terminal of the battery. Slide the cable off of the terminal and tuck it to the side of the battery. You will not need to disconnect the positive terminal. Locate the serpentine belt.
How can I increase the tension on my serpentine belt?
Increase the tension on the belt. If your vehicle does not have an auto tensioner, insert a pry bar or piece of wood between the alternator and the engine. Run the belt over the alternator pulley, then use the bar to pry the alternator away from the engine and increase the tension on the belt.
When to replace the serpentine belt in a Nissan Sentra?
Many vehicles have a main drive belt or serpentine belt, but Nissan Sentra models may have two main belts that the manufacturer suggests checking for wear every 7500 miles or 6 months and replacing as necessary.
How do you change a serpentine belt on a car?
Belt tensioners are mostly spring tension. Once installed, the spring retains pressure to the belt. Once on, make sure the belt is completely on and centered on each pulley very carefully. Then, start the engine. Let the engine idle for at least 60 seconds as you make sure the serpentine belt is working correctly.
Where is the alternator adjustment bolt on a Nissan Sentra?
The alternator adjustment bolt is often underneath the water pump hose. Install the new belt by putting it onto the pulleys in the same way that you got the old belt off. Nissan generally includes a belt routing diagram on a decal under the hood.
How is the tension set on a serpentine belt?
Depending on the application, your serpentine belt will either have tension placed on it using a movable bracket or an auto tensioner pulley. This pulley uses an internal spring to apply consistent pressure to the belt at all times. If your vehicle does not have a tensioner pulley, the alternator bracket is likely how tension is set on the belt.