How do you remove a fuel pump from a car?
First, you’ll need to remove the old fuel pump in this order: Disconnect the negative battery cable. Disconnect the fuel tank hose at the fuel pump and plug the hose with a bolt or wooden dowel to keep any fuel from flowing out. Also, disconnect the vapor-return hose if the vehicle is equipped with one. Be sure to wipe up any gas that spills.
Is the fuel pump on my Nissan 1400 1985 working?
Clide Tshuma on October 16, 2019: I’m sitting here with my nissan 1400 1985 model is not pumping fuel to curburater but when you fill 2 litter bottle with petrol it drives well I need your help Dwayne Oxford on February 28, 2019:
How long does a Nissan fuel pump relay last?
A factory relay is labeled Jideco, and if you choose to replace it, they seem to last about 20 years. On the back of the assembly are four Phillips screws. Once removed, the cover and insulator come off and you’re looking at the circuit board of the relay itself.
Where is the fuel pump wire located on a Nissan?
Why Nissan used a white/black wire from the relay to the body harness connector (found under the carpet beneath the passenger’s seat) is a mystery to me. All other fuel-related wires throughout the truck are brown as is the connecting terminal in the body harness connector which goes directly to the fuel pump.
Where is the fuel pump on a Nissan Hardbody?
Your Hardbody Pickup (1986.5-1994) fuel pump is powered by electricity, and is mounted either in the tank or along the frame rails. When replacing a Nissan Hardbody Pickup (1986.5-1994) fuel pump in your car or truck, be sure to install a new fuel filter and/or strainer.
How do you remove fuel pump from Datsun?
Remove the attached relay (s) and then undo the two screws holding the fuel pump relay to the panel. I found it easiest to remove the knee bar and heater blower motor first, but if you have very short screwdrivers and small hands, you can probably manage less disassembly than I did.
A factory relay is labeled Jideco, and if you choose to replace it, they seem to last about 20 years. On the back of the assembly are four Phillips screws. Once removed, the cover and insulator come off and you’re looking at the circuit board of the relay itself.
How do you replace a fuel pump in a car?
Connect the line to the fuel pump, and then reattach the other end to the carburetor. Use a wrench to hold the fuel pump fitting and tighten the line nut with another wrench. Attach the fuel inlet hose from the gas tank and the vapor-return hose. Tighten all clamps. Reconnect the battery ground cable, start the vehicle, and check for leaks.
Clean the top of the tank around the existing fuel pump assembly to prevent any dirt or debris from falling into the tank during removal. Refer to your service manual for instructions on removing the fuel pump assembly from the tank. There’s typically a plate held in place with screws or bolts, which, once released, enables removal of the pump.
When was the last time I replaced a fuel pump?
On the other hand, a repair job that goes awry can lead to frustration, swearing and bloody knuckles. The last time I replaced a fuel pump, I tackled the job outside, on the ground in the middle of a dust storm. Because the fuel tank had to be dropped to access the pump, the process took a couple of hours.
How big is a siphon fuel removal pump?
Only 3 left in stock – order soon. Plumber’s Siphon Pro – Gas, Oil, Water – Up to 3.5 Gl. Per Min. ONLY Siphon With Multi-size Tip Designed to Fit Any Hose.Comes with 9 ft. Hose. Brass Tip Weight or Extender – See Video in Pictures
What should I do if my fuel pump slides out?
Make sure that push rod is correctly installed in both the engine and the fuel pump. If the push rod slides out, you can pack it with some heavy grease to hold it in place while you install the pump. Attach the fuel outlet line that runs to the carburetor.