Why does my pilot light not stay on?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Why does my hot water pilot light keep going out?
If the pilot light goes out, the thermocouple senses the drop in temperature and signals for the gas valve to close. If you have a faulty thermocouple is the most common reason that your pilot light is malfunctioning. Over time your water heater will collect dirt, dust and other kinds of debris.
Why does my Procom heater keep turning off?
During operation, if the pilot light’s flame has been extinguished for any reason, the thermocouple cools and the gas valve will shut to stop the unburned gas from leaking out. If either the pilot light or the thermocouple aren’t working correctly, the burner will turn off.
Why does my gas wall heater keep going off?
If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.
How do you reset the climate control unit?
“Your Climate control unit may have to be reset. The reset works as follows: With the key in the ignition and in posistion 2 push both the defrost button and the recirc button (at the same time) for five seconds or untill the led lights in those buttons begin to flash. Wait for 30 seconds or untill the led’s stop flashing. Switch off the ignition.
Are there any back lights for climate control?
I have no back lights for my climate control. Anyone know if this is a huge problem or a simple fix. Obviously this picture with the cabin lights off. those have very small bulbs behind them and they can be changed. Most people replace them with LED’s. There is a write up somewhere here. please if u can show me direction.
Why does the EC light stay on all the time?
The EC light stayed on all the time. I replace the evap temp sensor and reg temp sensor, thanks to sleepwalker’s help. Then I recharged the system with freon and 46 PAG oil. By the way you must get the compressor to come on to charge the AC if your’s won’t come on, then hold down EC and Rest until the EC light goes off, the compressor will kick on.
What do you call a Mercedes climate control reset?
Sometimes, the process is called a Mercedes climate control reset. The reset procedure is similar no matter whatever you call it. However, if the AC shows any trouble after resetting, you have to take it to a servicing shop or the dealership for a permanent fix.
“Your Climate control unit may have to be reset. The reset works as follows: With the key in the ignition and in posistion 2 push both the defrost button and the recirc button (at the same time) for five seconds or untill the led lights in those buttons begin to flash. Wait for 30 seconds or untill the led’s stop flashing. Switch off the ignition.
I have no back lights for my climate control. Anyone know if this is a huge problem or a simple fix. Obviously this picture with the cabin lights off. those have very small bulbs behind them and they can be changed. Most people replace them with LED’s. There is a write up somewhere here. please if u can show me direction.
What to do if your climate control is not working?
Instead a communication wire passes through all modules informing the HVAC module how the lights should be operated. However, since the problem exists only with the HVAC, it is the component to blame. The solution is to replace the HVAC control module since the lights are internal and cannot be replaced.
Why does my climate control go off at idle?
The system is probably low on Freon and when the car is at idle, there is no load on the system and it operates. On the other hand, while driving the system is under load making the pressure go below the low pressure cut-off switches’ parameter. This switch turns off the compressor to prevent damage in the event of a low charge.