How to replace power window motor on Firebird?
Once loose, lift up and away from the door to remove the panel. Carefully peel back the plastic moisture shield away from the door skin so that you don’t rip it.
How to fix a bad electric window switch?
Attach the multimeter to the wires, then activate the window switch with the car’s key in the on position. If you are getting power in both directions of the switch, then the electrical wiring to the motor is good, and the motor should be replaced.
How to fix a window with a blown fuse?
1 Locate and check the fuse for the problematic window motor. If it’s blown, replace the fuse. 2 Remove the door panel. Locate the securing screws, usually behind covers or trim, and undo them. 3 Check the electrical input on the power and ground wires, which are generally the two largest wires connected to the window motor. …
What happens when I Fix my power window motor?
When we fix your side power window, the motor will work exactly how it used to before it needed service. The best part: We’ll fix your window fast and efficiently, so you can get back to using it quickly. You operate your power windows more often than you probably think.
What’s the problem with the power window on a Firebird?
Passenger power window rolls up very slow, almost stops. Drivers side window goes down but won’t go back up. Needs new motor. We have two 2002 firebirds and have replaced all 4 window motors due to motor failure even with little use. Two replacements of window motor on the passenger side did not fix the problem.
How to replace power window on Camaro Firebird?
Disconnect the electrical connection on the back of the panel by twisting it and pulling it out. Remove the two screws located underneath the arm rest and the one located down in the door pocket. Remove the Phillips screw just below the door handle. Remove the screw from the side mirror and pull the cover off.
How much does it cost to replace a window regulator on a Pontiac Firebird?
A door window may move slowly or stop in mid travel due to a failing power window motor. The affected window may start working again after the motor cools off. Replacing the faulty window motor will commonly correct this concern. The average cost for a Pontiac Firebird Window Regulator Motor Replacement is between $258 -$301.
What should I do if my power window is stuck?
Stick a piece of wood into the frame to hold the window in place. Locate the motor and remove the bolts/nuts: Find the motor in the door. It’s often located in the top right of the frame. Remove the bolts and nuts holding it in place.
How do you replace a power window motor on a Camaro?
Simply screw the new motor in. Once complete, slide the door panel back in place and push down around the edges to secure it in the clips. Replace the five screws in the panel, and you’re done! Figure 3.
Where are the Phillips screws on a Camaro Firebird?
Remove the two screws located underneath the arm rest and the one located down in the door pocket. Remove the Phillips screw just below the door handle. Remove the screw from the side mirror and pull the cover off. Pull up and out on the door panel to remove it.
Where are the rivets on a Camaro power window?
The three circled holes in Figure 2 are the ones you will need to drill to access the three rivets. In the picture, you can see approximately how far over these rivets are located from the exposed rivets. Once you drill the holes, drill out the rivets. Disconnect the wiring harness from the motor and remove it.
Once loose, lift up and away from the door to remove the panel. Carefully peel back the plastic moisture shield away from the door skin so that you don’t rip it.
Simply screw the new motor in. Once complete, slide the door panel back in place and push down around the edges to secure it in the clips. Replace the five screws in the panel, and you’re done! Figure 3.
What happens if your power window motor fails?
While some folks get lucky and have a little warning of their power window motor’s impending demise, most of us suffer from a “surprise” moment of failure. You may get stuck with a lowered window in the cold or pouring rain, or a window that won’t roll down when you’re just trying to get some drive-through grub.
The three circled holes in Figure 2 are the ones you will need to drill to access the three rivets. In the picture, you can see approximately how far over these rivets are located from the exposed rivets. Once you drill the holes, drill out the rivets. Disconnect the wiring harness from the motor and remove it.