How to remove AWD from a Nissan Rogue?
Remove the wheel hub lock nut. Remove the hub bolts and the wheel hub and bearing. Position the parking brake and back plate aside with wire. Remove the coil spring and spring seats. Refer to RSU-10, “Removal and Installation – AWD”. Remove the axle housing.
What kind of engine does the Nissan Rogue have?
performance & mpg. The 2010 Nissan Rogue is available with either front- or all-wheel drive. It’s powered by a 2.5-liter four-cylinder engine that produces 170 horsepower and 175 pound-feet of torque and employs a CVT.
How big are the wheels on a Nissan Rogue?
The 2010 Nissan Rogue is a five-passenger compact crossover SUV available in S, S Krom Edition or SL trim. The base S comes standard with 16-inch steel wheels, cruise control, a tilt (but non-telescoping) steering wheel, air-conditioning, full power accessories, keyless entry and a four-speaker audio system with a CD player and an auxiliary jack.
How to remove rear wheel sensor from Nissan Rogue?
Refer to WT-57, “Adjustment”. Remove the bolt and separate the rear wheel sensor from the axle housing. Position the rear wheel sensor and the harness aside. Refer to BRC-134, “REAR WHEEL SENSOR : Removal and Installation”. Pull out the rear wheel sensor, being careful to turn it as little as possible.
Is the 2010 Nissan Rogue safe to drive?
My 2010 Nissan Rouge is one of the many 2008-2010 Nissan Rogue vehicles that are defected. It has same continuous transmission problem, it is unsafe to drive in a highway. However, Nissan does not do a recall.
How do you replace a Nissan Rogue battery?
Battery Replacement: 2008-2013 Nissan Rogue – 2010 Nissan Rogue SL 2.5L 4 Cyl. 1. Getting Started – Prepare for the repair 2. Open the Hood – How to pop the hood and prop it open 3. Access Battery – Learn where the battery is located 4. Remove Bracket – Take off the bracket that secures the battery 5.
What’s the warranty on a 2010 Nissan Rogue?
Be aware CVT on 2010 is warranted to 120,000 miles, mine failed at 108,000 & luckily Nissan dealership made me aware of warranty (3500.00). At time when transmission failed (RPM rev up to 6500), AC stopped working immediately ($1000.00), according to dealership no relation between trans & AC failure.
What kind of transmission does the Nissan Rogue have?
Favorite Features. Nissan’s Xtronic Continuously Variable Transmission (CVT) Nissan is one of the few automakers to still embrace and refine CVT technology, and this second-generation transmission is incredibly smooth and gives the Rogue decent performance as well as good fuel economy.
How to remove drive shaft from Nissan Rogue?
Loosen, but do not remove, the wheel hub lock nut from the drive shaft using power tool. Tap the wheel hub lock nut with a piece of wood to disengage the drive shaft from the wheel hub and bearing. Do not place drive shaft joint at an extreme angle. Be careful not to overextend slide joint. Do not allow drive shaft to hang without support.
How to install a disc brake on a Nissan Rogue?
Tighten the wheel hub lock nut to the specification. When installing a the cotter pin (1) and the nut retainer (2), securely bend the cotter pin to prevent rattles. Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing. Complete the inspection.
Remove the wheel hub lock nut. Remove the hub bolts and the wheel hub and bearing. Position the parking brake and back plate aside with wire. Remove the coil spring and spring seats. Refer to RSU-10, “Removal and Installation – AWD”. Remove the axle housing.
Loosen, but do not remove, the wheel hub lock nut from the drive shaft using power tool. Tap the wheel hub lock nut with a piece of wood to disengage the drive shaft from the wheel hub and bearing. Do not place drive shaft joint at an extreme angle. Be careful not to overextend slide joint. Do not allow drive shaft to hang without support.
Refer to WT-57, “Adjustment”. Remove the bolt and separate the rear wheel sensor from the axle housing. Position the rear wheel sensor and the harness aside. Refer to BRC-134, “REAR WHEEL SENSOR : Removal and Installation”. Pull out the rear wheel sensor, being careful to turn it as little as possible.
How to install wheel studs on Nissan Rogue?
Place a washer (A) as shown to install the wheel studs (1) by using the tightening force of the nut (B). CAUTION: Check that there is no clearance between the wheel stud and the wheel hub and bearing. Clean the mating surfaces of the wheel hub lock nut and the wheel hub and bearing. CAUTION: Do not apply lubricating oil to these mating surfaces.