What is the Nissan Altima camshaft sensor code?

2004 Nissan Maxima Nissan Factory Service Bulletin OBDII Code P0340 Camshaft Positioning Sensor Replacement – Nissan Altima User Submitted Video What does this mean? Cost of diagnosing the P0340 NISSAN code Labor: 1.0 The cost of diagnosing the P0340 NISSAN code is 1.0 hour of labor.

What kind of engine does a Nissan Altima have?

All Altima models used Nissan’s 150 hp (112 kW) KA24DE straight-4 DOHC engine mated to a 5-speed manual or 4-speed automatic (Acceleration performance: 9.4 seconds 0-60 mph (100 km/h) with automatic and 8.4 with manual). Get notified for new files? We’ll send you a quick email when a new Nissan Altima document is added.

Are there any manuals for the Nissan Altima?

Every Manual available online – found by our community and shared for FREE. Enjoy! The Nissan Altima is a mid-size car manufactured by Nissan, and is a continuation of the Nissan Bluebird line, which began in 1957. It is the #1 selling Nissan model.

What does the camshaft position sensor do in a Nissan?

P0340 NISSAN Description The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module (ECM) to control ignition and fuel injection.

What’s the camshaft code on a Nissan Maxima?

2006 Nissan pathfinder 89000 miles I changed all sensors bank 1 bank 2 and camshaft sensors than changed the variable timing solenoids both of them . changed oil twice . still the code p0021 keeps showing up . the truck runs great .but dies randomly on the hwy? what can I check next …. Hi, I just bought a 2005 Nissan Maxima with 109500 miles.

What is the engine code for the a camshaft?

In this case, if the cam timing is above a set limit (over-advanced), the engine light will be illluminated and the code will be set. The “A” camshaft is either the intake, left, or front camshaft. A P0021 engine code is basically the same as a P0011 code, except this is for Bank 2, not Bank 1.

What causes a Nissan camshaft sensor to malfunction?

P0340 NISSAN Possible Causes 1 Faulty Camshaft Position Sensor 2 Camshaft Position Sensor harness is open or shorted 3 Camshaft Position Sensor circuit poor electrical connection 4 Faulty starter motor 5 Starting system circuit 6 Dead (Weak) battery

What is the p0340 Nissan camshaft position sensor?

P0340 Nissan Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.

How to fix code p0340 on Nissan Leaf?

How do I fix code P0340 NISSAN Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. P0340 NISSAN Tech Notes Nissan models with distributor the camshaft position sensor is part of the distributor.

Can you do a self diagnostic on a 99 Altima?

I believe you have a ’99 Altima, right? If so, then you should still be able to do a self-diagnostic directly on the ECU itself. There are a whole lot of write-ups on this site on how to do that.

Where is the OBD2 port on a Nissan Altima?

The Don. The grey plug inside the fusebox is the CONSULT port, it is rectangular in shape, and has 14 pins. The OBD2 port should sits underneath the fusebox, the sides runs diagonally, and it has 16 pins. If the OBD2 is truly unreadable by any scanner then it is probably missing either power or ground to that port. ’94 Nissan Altima SE, 5spd.

When is the p0340 Nissan code detected?

Labor: 1.0 The cost of diagnosing the P0340 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0340 NISSAN code detected?

Navigation