What does a p0014 Nissan engine code mean?
Since the exhaust valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code. What does this mean? The cost of diagnosing the P0014 NISSAN code is 1.0 hour of labor.
How to troubleshoot DTC p0014 on Nissan Sentra?
If DTC P0014 is displayed with DTC P0078, first perform trouble diagnosis for DTC P0078. Refer to EC-183, “DTC Logic”. If DTC P0014 is displayed with P1078, first perform trouble diagnosis for P1078. Refer to EC-359, “DTC Logic”. There is a gap between angle of target and phase-control angle degree.
What to do if DTC p0014 is displayed?
If DTC P0014 is displayed with P1078, first perform trouble diagnosis for P1078. Refer to EC-359, “DTC Logic”. There is a gap between angle of target and phase-control angle degree. If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
How to clear ECU memory on Nissan Pathfinder?
A forum for the legendary Nissan Pathfinder and Infiniti QX4. The following procedures will allow you to clear the ECU memory as well as erase any DTC codes which may illuminate your SERVICE ENGINE SOON lamp.
How much does it cost to diagnose Nissan p0014 code?
The cost of diagnosing the P0014 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0014 NISSAN code detected?
If DTC P0014 is displayed with DTC P0078, first perform trouble diagnosis for DTC P0078. Refer to EC-183, “DTC Logic”. If DTC P0014 is displayed with P1078, first perform trouble diagnosis for P1078. Refer to EC-359, “DTC Logic”. There is a gap between angle of target and phase-control angle degree.
What causes the p0014 engine code to reset?
Since the exhaust valve timing control solenoid valve uses oil flow to control timing, dirty oil can cause the valve to stuck open or close. Before replacing the valve, change engine oil and filter and reset engine code. The cost to diagnose the P0014 NISSAN code is 1.0 hour of labor.
If DTC P0014 is displayed with P1078, first perform trouble diagnosis for P1078. Refer to EC-359, “DTC Logic”. There is a gap between angle of target and phase-control angle degree. If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
Where is Bank 1 on a p0014 engine?
Bank 1 is the side of the engine containing cylinder #1. The “B” camshaft shall be either the “exhaust,” “right,” or “rear” camshaft. Left/Right and Front/Rear are determined as if viewed from the driver’s seating position. Most likely a P0014 DTC will result in one of the following: hard starting, poor idle, and/or stalling.
What happens when a p0014 DTC is set?
Most likely a P0014 DTC will result in one of the following: hard starting, poor idle, and/or stalling. There are potentially other symptoms as well. Of course, when trouble codes are set, the MIL (malfunction indicator lamp, a.k.a. the check engine light) illuminates.
What does the OBD-2 error code p-0014 mean?
The OBD-II error code P-0014 is typically related to an over adjusted timing issue detected by the camshaft sensor as opposed to a damaged sensor itself, which leads me to think that it’s either… Read more
What does the code p0014 mean on a car?
The code can refer to a problem with either the variable valve timing or variable camshaft timing systems and the powertrain control module or engine control module. VVT alters how long cylinder valves are open for at a time.
How does the p0014 camshaft position actuator work?
P0014 Description. The Camshaft Position (CMP) actuator is attached to each camshaft and is hydraulically operated in order to change the angle of the camshaft relative to Crankshaft Position (CKP). The CMP actuator solenoid is controlled by the control module.
Bank 1 is the side of the engine containing cylinder #1. The “B” camshaft shall be either the “exhaust,” “right,” or “rear” camshaft. Left/Right and Front/Rear are determined as if viewed from the driver’s seating position. Most likely a P0014 DTC will result in one of the following: hard starting, poor idle, and/or stalling.
How much does it cost to repair a Nissan p0014?
The cost of diagnosing the P0014 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.