What are the possible causes of Nissan p0744?

P0744 NISSAN Possible Causes 1 Faulty torque converter clutch solenoid valve 2 Torque converter clutch solenoid valve harness is open or shorted 3 Torque converter clutch solenoid valve circuit poor electrical connection 4 Low transmission fluid level 5 Dirty transmission fluid

What causes the p0744 code to be stored?

The P0744 code may be stored if the torque converter clutch solenoid is faulty, or if the torque converter is defective. Other causes may include: Blocked internal transmission fluid passages. Mechanical internal transmission failure.

Why is my torque converter clutch code p0744?

The P0744 code is primarily set by mechanical faults such as sticking Torque Converter Clutch (TCC) solenoid or valves in valve body. Since the problem continues after you replaced the transmission fluid, then you may have a problem with the Transmission Valve Body.

Is the ODBII code p0744 an extended warranty?

ODBII CODE P0744 No Extended Warranty… This was the second time this happened to me. I was driving 80 mph on the highway about 2 weeks ago when I heard a relatively whining sound which resulted in loss of power.

What are the symptoms of a p0744 trouble code?

The symptoms of the P0744 code can vary. There may be no detectable symptoms at all beyond the illumination of the Check Engine Light. However, symptoms could be as dire as the total failure of the torque converter clutch to disengage.

How much does it cost to diagnose Nissan code p0744?

Labor: 1.0 The cost of diagnosing the P0744 NISSAN code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. When is the P0744 NISSAN code detected?

What are the symptoms of p0744 OBD-2 trouble code?

What does p0744 mean on a 2006 maxima?

2006 maxima loses power, hard shifting, got code p0744, what does it mean… I have code P0744 on 98 Mercury Villager w/122,000 miles. Service Engine light is on. What does this means specifically?

What does the p0744 code on a PCM mean?

If the PCM has stored the P0744 code, it means that there was an intermittent abnormality detected in the torque converter clutch circuit.

What causes an OBDII code on a Nissan Rogue?

This is not only caused by electrical malfunctions (circuits open or shorted), but also by mechanical malfunctions such as control valve sticking, improper solenoid valve operation, etc. Need more information on how to fix the P0744 2013 NISSAN ROGUE code?

How to check a Nissan OBDII engine code?

First diagnose P0744 NISSAN code. Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded terminals.

What does p0744 mean on a torque converter?

Note that code P0744 rarely indicates a faulty transmission, or a general failure of mechanical components in the transmission or torque converter.

What’s the ODBII code for Nissan torque converter?

Anyways I pulled the code which is P0744 Nissan – Torque Converter Clutch Circuit Intermittent Unfortunately, I don’t have the extended warranty only the basic. What are the possibilities of my situation and how expensive will it cost to fix this?

Note that code P0744 rarely indicates a faulty transmission, or a general failure of mechanical components in the transmission or torque converter.

Why is my Nissan OBDII light not working?

P0744 NISSAN Tech Notes When the a transmission solenoid is working intermittent, in most cases the problem is not the electrical part of the solenoid; the problem is foreign material obstructing the mechanical function of the solenoid or the flow of the fluid through the transmission valve body.

What are the error codes for CVT transmission?

Codes: P1778, P0746 and P0868: Hi All, My Car Has a CVT XTRONIC My car has a CVT XTRONIC transmission. A quick summary of my question: my car is diagnosed with these error codes;P0746, P1778 and P0868. Do I need to replace the transmission? Or a transmission specialist would be able to fix the issues?

How to replace CVT body on versa Sentra?

INSTALLATION 1. Install the control valve, and then tighten control valve bolts to the specified torque. CAUTION: 窶｢ Never pinch the harness between the control valve and the transaxle case. 窶｢ Never drop the control valve and manual valve. 2. Install the manual plate and washer , and then tighten nut to the specified torque.

What to do if your torque converter code is p0744?

There are many ways that a technician can address a P0744 code, including: Checking and replacing transmission fluid; if the fluid is found to be very dirty, flushing the system and replacing the torque converter may be required. Checking and replacing any shorted or faulty wiring, connectors, and circuitry.

What does the p1701 code on a rogue mean?

The P1701 code is not common at all on the 2013 Rogue. The code means there is no power or at some point the TCM lost power. Have you done any repairs lately? disconnect the car battery? You remove the the component connector, check the connector and make sure there is no corrosion, and then firmly reconnect the connector. Clear the codes.

How to diagnose p1701 Nissan Transmission Control Module?

Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. How much do you know about cars? What does this mean? The cost of diagnosing the P1701 NISSAN code is 1.0 hour of labor.

How much does it cost to repair a Nissan p0740?

The cost of diagnosing the P0740 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

What does the Diagnostic Code p0740 mean?

Diagnostic trouble code P0740 is detected when TCM detects an improper voltage drop when it tries to operate the solenoid valve. The torque converter clutch solenoid valve is activated, with the gear in D4, by the Transmission Control Module (TCM) in response to signals sent from the vehicle speed and the Engine Control Module ( ECM ).

What does intermittent DTC mean on Nissan Pathfinder?

If the cycle is intermittent on rough road conditions, it may be a wiring fault. Re-check connections and if all wiring / solenoid is OK or if road conditions do not coincide with the intermittent readings, the TCM may be at fault. I have a 2001 Nissan Pathfinder and I am getting a P0744 code for it.

Is the Nissan Xterra the same as the Nissan Terra?

Not to be confused with Nissan Terra. “Nissan X-Terra” redirects here. For the SUV sold in the Middle East with the same name since 2020, see Nissan Terra.

What’s the difference between a Chinese and American Xterra?

Other difference between the American Xterra and its Chinese counterparts is the parking brake actuator, a pedal with a pull-handle release in America, and a lever in China. Dongfeng Motors produces a Chinese version of the Xterra called the Oting from 2007 to 2015. It is based on the first generation of the Xterra.

What’s the difference between the Xterra generations of the Jeep Cherokee?

While the two Xterra generations differed significantly, both prioritized ruggedness and affordability over luxury and used body-on-frame construction along with underbody skid plates.

How much does it cost to diagnose a p0744 code?

The cost of diagnosing the P0744 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

Where can I find the ODB-II code for a Nissan?

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Nissan makes. 2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

Why does my Nissan Altima make a whining noise when accelerating?

A whining sound when accelerating is almost always caused by a bad accessory attached to your Altima’s engine. Here are the most common causes of whining noises when accelerating: 1. Bad Alternator When an alternator is going bad, it’ll often begin to put out a high pitched whining sound. It should also be accompanied by the battery light.

If the PCM has stored the P0744 code, it means that there was an intermittent abnormality detected in the torque converter clutch circuit.

Why does my alternator make a whining noise?

Alternator whine is a product of a drop in voltage between the radio and the alternator itself. It is usually way more noticeable on the A.M band of the radio. You’ll hear it match the acceleration of the vehicle.

2006 maxima loses power, hard shifting, got code p0744, what does it mean… I have code P0744 on 98 Mercury Villager w/122,000 miles. Service Engine light is on. What does this means specifically?

Symptoms of a P0744 trouble code may include: Intermittent Indicator Lamp (MIL) illuminated (a.k.a. Check Engine Light) Minimal decrease in fuel economy, this will not affect engine performance Causes of this DTC may include: Wiring harness to transmission damaged, loose connection, or intermittent open/short circuit

What are the possible causes of a Nissan loss?

P0744 Nissan Possible Causes. Faulty torque converter clutch solenoid valve. Torque converter clutch solenoid valve harness is open or shorted. Torque converter clutch solenoid valve circuit poor electrical connection. Low transmission fluid level. Dirty transmission fluid.

What causes a transmission solenoid to stop working?

When the a transmission solenoid is working intermittent, in most cases the problem is not the electrical part of the solenoid; the problem is foreign material obstructing the mechanical function of the solenoid or the flow of the fluid through the transmission valve body.

What is the service code for a Nissan Maxima?

Code p1140 indicates that with the engine running the PC detected an … read more MY NISSAN MAXIMA KEEP LOSS POWER. 2010. NOTHING YET. I PAID MY NISSAN MAXIMA KEEP LOSS POWER JA: What year is your Maxima? Customer: 2010 JA: Are you fixing your Maxima yourself? What … read more Service enhine soon light on error code p0744. Just had it

What causes the p0174 code on a Nissan Murano?

Vacuum Leaks – With the Nissan Murano, the most common cause for the P0174 code to show is a vacuum leak. Take a look around and see if you can find the vacuum leak. Here’s a great YouTube video on how to find a vacuum leak. Mass Air Flow Sensor – The mass air flow sensor calculates the volume of air entering the engine.

What is the OBDII code for a Nissan Murano?

This code number references a number that is given to you when you plug your truck into a OBDII scanner. The code is often accompanied by the P0171 code, which has the same set of symptoms, but is for bank one. Bank 1 and Bank2 refer to the side of the engine with cylinder 1 and 2 in the firing order respectively. P0174 is an OBDII trouble code.

Navigation