Why is my Nissan Almera not working properly?
The first failure that appeared and was detected by the scanner was a crankshaft sensor damage. It was replaced together with a coil that was failing too. The car worked properly for some days, until the engine started vibrating and losing power. This got worse with time and, today, it does not accelerate nor work properly any longer.
What to do if your Almera engine is failing?
Check the crankshaft sensor and scan your vehicle to see the codes provided. If it is the alarm that is failing, that occurred to me and the whole alarm system needed to be disconnected. After doing so, the car never failed again. Thanks for all your comments.
What to do if your Nissan Almera stalls?
The vehicle occasionally stalls and starts without a problem. But there are some other occasions, which have been more frequent lately, in which the engine does not start working again after it stalls. You need to change both the crankshaft and camshaft sensors and then reset your computer.
Can a Sentra sensor be replaced in a Nissan Almera?
You can try replacing yours with a Sentra or an Altima sensor, good luck. Good afternoon, I have a Nissan Almera 2007, which starts but does not accelerate. The first failure that appeared and was detected by the scanner was a crankshaft sensor damage.
Are there any problems with my Nissan Almera?
My Nissan Almera 1.8 2005 starts normaly and after 25-30 km the engine stops working and can not be started 1-2 minutes, after starting, the problem repeats in shorter period. The check indicator is turned on. I have made computer diagnostic and it shows 3 errors:
Why does my Nissan Almera stutter when I Rev the engine?
Your Almera starts fine, but it stutters and sometimes cuts out when you rev the engine. This could be a variety of issues. Your first step should be to check the airflow sensor and then test that the fuel pump is working correctly.
Check the crankshaft sensor and scan your vehicle to see the codes provided. If it is the alarm that is failing, that occurred to me and the whole alarm system needed to be disconnected. After doing so, the car never failed again. Thanks for all your comments.
The vehicle occasionally stalls and starts without a problem. But there are some other occasions, which have been more frequent lately, in which the engine does not start working again after it stalls. You need to change both the crankshaft and camshaft sensors and then reset your computer.
What’s the engine code on a Nissan Almera?
Engine on tickover Idles at 1500 revs: driving , engine hunts between gear changes at 1800 to 2500 rpm Got nats codes 1610 & 1612 engine cranks but no start no spark at plugs. Nats light on dash continuously flashes.
Why does my Nissan Almera make a hissing noise?
The engine is running rough, and there is a hissing noise coming from it, although there are no problems revealed when you do a fault check. Most likely, this is a problem with your airflow meter.
What are the problems with my Nissan Almera?
Changed timing chain and sensors car wont start. Fuel and spark working. Got nats codes 1610 & 1612 engine cranks but no start no spark at plugs. Nats light on dash continuously flashes. Any ideas thanks The engine light came on, l scanned to find fault on bank 1 sensor 1which I replace, only for it to show bank 2 sensor 2 again.
You can try replacing yours with a Sentra or an Altima sensor, good luck. Good afternoon, I have a Nissan Almera 2007, which starts but does not accelerate. The first failure that appeared and was detected by the scanner was a crankshaft sensor damage.
What are the Nats codes for Nissan Almera?
Got nats codes 1610 & 1612 engine cranks but no start no spark at plugs. Nats light on dash continuously flashes. Any ideas thanks The engine light came on, l scanned to find fault on bank 1 sensor 1which I replace, only for it to show bank 2 sensor 2 again.