How to read NISSAN OBD 1 codes without OBD scanner?

How To Read (Retrieve) Nissan OBD 1 Codes without OBD Scanner. Easy way to read, accessing, erasing and resetting obd1 codes on nissan cars. Trouble codes are displayed by the malfunction indicator lamp (MIL). The ECM fault memory can also be checked using diagnostic equipment connected to the data link connector (DLC).

Is there a way to read a Nissan fault code?

Check (if you live in usa): Kroger Weekly Ad, or Myer catalogue. Nissan ECU’s allow you to read any stored fault codes without any specialist equipment. Below will show how you can read yours. The orientation of the plug may vary so please make sure you are looking at the plug the right way up before you try this on your car.

How do you read the ECU code on a Nissan?

Press and hold the gas pedal for 12 seconds then release. Check Engine Light (CEL) will blink 10 times slowly before the codes are displayed. CEL will blink rapidly when displaying the codes, count the number of rapid blinks between the pauses.

How to clear engine codes without a Nissan consult or scan tool?

How to clear the engine codes without a Nissan CONSULT or scan tool. Set ECM in Diagnostic Test Mode II (Self-diagnostic results). Fully depress the accelerator pedal and keep it for more than 10 seconds. The emission-related diagnostic information has been erased from the backup memory in the ECM.

How to read engine OBDII Codes without Nissan scan tool?

In this way, all the detected malfunctions are classified by their DTC numbers. The DTC 0000 refers to no malfunction. How to read the engine codes without a Nissan CONSULT or scan tool. (Set ECM in Diagnostic Test Mode II) Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.

How do you find the fault code on a Nissan?

Turn the ‘diagnostic mode selector’ screw on the computer fully clockwise. The check engine light will go off. Wait 5 seconds, then turn the screw fully counter clockwise. 3. The check engine light will then begin to flash stored fault codes. The long flash (s) = 1st digit; short flashes = 2nd digit. 4.

Where do I find the ECU fault code?

ECU fault codes are usually displayed on the engine check light on the dash, and are displayed by the number of flashes as well as the speed of the flashes. For example, an ECU showing no recorded faults will display code 55. The first digit is shown as 5 followed by a pause. This then followed by the second digit.

What does code 12.4 mean on Nissan OBD?

Meaning: One red flash and two green flashes means code 12. 4. To clear the ECU of any trouble codes, move the switch to the “DIAGNOSTICS” position then back to the “ON” position and turn off the key.

Why is the OBD-2 port not powered?

The OBD-II reader could not communicate with the car with the key on accessory, but when he started the car, he was able to pull off three codes. One was a fuel level fault, and he other two were OBD-II related faults. So, I’m still thinking that there is a power issue with the OBD-II port.

Where is the fuse on a Nissan OBD-2?

I am told by an Infiniti tech that the fuse is a 10 amp fuse in slot number 12, on the far left bottom row. The legend for that fuse is “ELEC PARTS”.

Why is the OBD II scanner not communicating?

Check the fuse box (Power Panel), it might be the reason why PCM isn’t able to receive power as well as communicate.

Where can I find the Nissan check engine light code?

P1492 EVAP Canister Purge Control/Solenoid Valve (Circuit) – Read Our Article On Automotive Circuit Testing For Help With This Nissan Check Engine Light Code P1705 Throttle Position Sensor Circuit A/T – Read Our Article On Automotive Circuit Testing For Help With This Nissan Check Engine Light Code

What is the EGR code for a Nissan check engine?

P1135 Intake Valve Timing Control Circuit (Bank 2) – Read Our Article On Automotive Circuit Testing For Help With This Nissan Check Engine Light Code P1402 EGR System – Read Our Article on EGR Valve Codes For Help With This Nissan Check Engine Light Code

How to put Nissan engine in diagnostic mode?

There are three methods of putting vehicles with this connector into diagnostic mode. If one does not work, try the others. Select one of the methods below. This is the prefered method. To select this method click ‘Connector Method’. Does not require a connector. To select this method click ‘Pedal Method’.

Which is the best diagnostic scanner for Nissan?

Similar to the Veepeak adapter above, the OBDLink MX+ OBD2 scanner uses Bluetooth to make any device into a Nissan diagnostic scan tool. Similar to the Veepeak adapter above, the OBDLink MX+ OBD2 scanner uses Bluetooth to make any device into a Nissan diagnostic scan tool.

What does a diagnostic code on a Nissan mean?

A diagnostic code is helpful when troubleshooting a particular problem that has occurred. After the trouble code is defined the problem can be repaired and rechecked. Early Nissan check engine lights are not used to blink out a trouble code like on most vehicles but instead use a mode and retrieval method.

How do I boot Nissan obd1-2 carpros?

Step 1 – To boot the computer in mode four make sure the key is in the “OFF” position. Next locate the mode switch on the computer which is either a small toggle or a screw style switch. The screw style switch is activated by turning the screw one way then back the other way.

Where is my OBD2 port in Nissan Almera?

The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate. To diagnose your vehicle yourself, download our EOBD-Facile car diagnostic software. Use our search engine below to locate your OBD2 port! 370 Z (2009 – …) Almera (2012 – …)

Why does my Nissan club not have a code reader?

On to your problem. That is the code that I had when I was running without a cat, and my rear O2 intercept was not working properly. It is one that WILL stay locked in the memory. It can refer to the MAF, but can also be caused by the rear O2 sensor as well.

Where to find Nissan check engine light codes?

These are listed in numerical order for easy searching. When retrieving Nissan check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.

Where is my OBD2 port in Nissan?

Where do I find the DTC code on my BMW?

Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3. Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).

Where can I find the OBD code on a Nissan Maxima?

Nissan Corporation OBD I diagnostic page explains how to get the codes without any special tools. The codes are listed seperately for Maxima and Sentra models as needed. The codes are defined as to what system is affected. When possible we give the more commonly known OBD II component name.

Navigation