What kind of torque does a Nissan Maxima have?
TORQUE SPECIFICATIONS NISSAN APPLICATION FT-LBS (N-m) AXLE SPINDLE NUT 1986-78 115 (157) 1994-87 ALTIMA, MAXIMA, STANZA, & QUEST 174-232 (237-316) PULSAR, SENTRA, 240SX, & 300ZX 145-203 (197-276) AXLE SHAFT-TO-SIDE FLANGE NUT 240SX & 300ZX NON-TURBO 25-33 (34-44) 300ZX TURBO (BOLT) 51-58 (68-78)
How big is the axle spindle nut on a Nissan?
NISSAN APPLICATION FT-LBS (N-m) AXLE SPINDLE NUT 1986-78 115 (157) 1994-87
What are torque specifications for front and rear axles?
Torque specification guide Front & rear axle nut torque specifications for FWD, RWD & 4 W/D vehicles One of the most common mistakes during installation is improper torque of the Axle nut. To guarantee the (Bearing, Spindle or Hub) is torqued correctly, follow the manufacture’s installation procedure.
What happens when an axle nut is over torque?
Under torque of an axle nut will allow excessive movement causing uneven loading and excessive wear. Over torque of the axle nut will cause excessive load and cause the bearing to overheat, this is one of the most common causes for failures.
How much torque does a front axle nut have?
Description: FWD, RWD & 4 W/D front axle nut torque specifications Front proc. Rear proc. Make or torque or torque year Model ft-lbs/Nm ft-lbs/Nm Front proc. Rear proc. No Text Content!
Torque specification guide Front & rear axle nut torque specifications for FWD, RWD & 4 W/D vehicles One of the most common mistakes during installation is improper torque of the Axle nut. To guarantee the (Bearing, Spindle or Hub) is torqued correctly, follow the manufacture’s installation procedure.
Can a impact gun damage an axle nut?
The impact gun will damage the axle nut. It will also leave your spindle nut under or over torque resulting in hub assembly failure. Ensure that you have the correct torque for the application by referring to SKF 457377 torque specification guide or contact the vehicle manufactures dealer.
Can a calibrated torque wrench install an axle?
Use a qualified, calibrated torque wrench. Do not use an impact gun to install the axle nut. The impact gun will damage the axle nut. It will also leave your spindle nut under or over torque resulting in hub assembly failure.
Where can I find the latest torque specs?
Find the most up-to-date torque spec listings in electronic format. FelPro-Only.com is your convenient source for advanced sealing information. It’s the place to learn and share “tricks of the trade,” find proper diagnosis and installation instructions, and enjoy easy access to parts reference.
What are the torque settings for head bolts?
SOURCE: head bolts torque settings According to my haynes manual for G-S reg, 1989-1998 it goes as follows, Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head. Stage 2:-Tighten all bolts to 40Nm or 30lb ft. Stage 3:-Angle tighten all bolts a further 60 degrees. Stage 4:-Angle tighten all bolts again a further 60 degrees.
What is the torque for the head bolt?
The medium-head bolts need 22 foot-pounds of torque and a 65-degree rotation. The long cylinder head bolts required 22 foot-pounds of torque and a 75-degree rotation.
What are torque specifications?
Torque specifications are for dry threads only. The fastener threads should be free of oil, dirt, grit, corrosion, etc. The hardware should turn freely without binding when tightened by hand. It is important NOT to lubricate hardware threads or seats. The friction at which torque is measured against should come from the hardware seats.
What is head bolt torque?
Head Bolt Torque. Head bolt torque refers to the amount of rotational force that must be applied to the cylinder head bolts for a safe and secure connection either to the engine block or another cylinder head depending upon the engine.
What are the torque specs on a Nissan Lugnut?
Front brake calipers, the two bolts that hold it on.Rear brake calipers, the two bolts that hold it on. All 16 lugnut torque specs also please. other than,”FRONT DISC BRAKE CALIPERRemovalRaise and support front of vehicle. Remove wheel assembly.Disconnect and plug brake line from caliper. Remove caliper mountbolts.
What are the torque specs for inner tie rods?
A forum for the legendary Nissan Pathfinder and Infiniti QX4. Outer/Inner Tie Rods – Torque Specs? I’m replacing those rusty Outer and Inner Tie Rods but have no idea how much torque I should be applying. Anyone has any idea? Thanks. Re: Outer/Inner Tie Rods – Torque Specs? Page ST-17 of the factory service manual should tell you.
What should the torque be on a cylinder head bolt?
The manufacturer usually stipulates that you must tighten the bolts in incremental steps. For example, suppose the final torque on a bolt is 40 foot-lbs. The manufacturer may state to bring all the bolts to 10 foot-lbs. first, following the torque sequence. In the second step, bring the torque to 20 foot-lbs.
Where to find torque specs for front wheel hub replacement?
ANSWER: Please scroll down to post #6 for the correct torque specs. And a link to a free on-line Factory Service Manual! Also see post #8 for replacement notes with pictures.
What are torque specs for 2004 Nissan Quest?
2004 Nissan Quest. Just replaced the front right-lower control arm. Need specs for torqueing the bolts. Thanks if you can help! 107 ft/lbs for the two bolts holding the inner rear bolts (if seated in vehicle looking forward).
What are the torque specs for Nissan front control?
107 ft/lbs for the two bolts holding the inner rear bolts (if seated in vehicle looking forward). 73 ft/lbs for the one inner front bolt. 56 ft/lbs for the outside bolt that holds the ball joint post into the bearing assembly. Can someone confirm these?
What are torque specs for front control arm?
Just replaced the front right-lower control arm. Need specs for torqueing the bolts. Thanks if you can help! 107 ft/lbs for the two bolts holding the inner rear bolts (if seated in vehicle looking forward). 73 ft/lbs for the one inner front bolt. 56 ft/lbs for the outside bolt that holds the ball joint post into the bearing assembly.
How to access AutoZone’s torque specifications repair guide?
Find out how to access AutoZone’s Torque Specifications Repair Guide for Grand Prix, Impala 2006-2008, Monte Carlo 2006-2007. Find out how to access AutoZone’s Torque Specifications Repair Guides.
Do you need a calibrated torque wrench to install an axle nut?
To guarantee the (Bearing, Spindle or Hub) is torqued correctly, follow the manufacture’s installation procedure. Ignoring these important details will reduce the life of your (Bearing, Spindle or Hub). Use a qualified, calibrated torque wrench. Do not use an impact gun to install the axle nut. The impact gun will damage the axle nut.
How to replace the rear wheel bearing on an Infiniti?
Loosen the four 19 mm bolts enough but not complete off the hub; using a hammer and whack each bolt a couple of times to un-seat it off the knuckle. Using a wire brush, clean off any rust and corrosion around the seat.