What kind of drive belt does a 2005 Nissan Maxima have?
by Grace Mclain. The 2005 Nissan Maxima comes equipped with two different drive belts on the front of the engine. The front belt is a serpentine belt. The serpentine belt controls the air conditioner pump and the alternator. The back belt is a regular drive belt. The drive belt controls the power steering pump.
How do you tighten a belt on a Nissan Maxima?
Tighten the lock nut down tight with the ratchet and socket. Then, crank the 2005 Nissan Maxima and let the engine run for 30 seconds. Turn the engine off and check the tension on the belt again. Close the hood. There is also a belt tension checking tool that can be used to properly tension the new serpentine belt.
How do you replace a belt on a car?
Tighten up the adjustment bolt to replace appropriate tension on the belt. Make sure the belt is seated on all pulleys. Tighten the lock bolt. Run the engine and observe to see if the belt is installed correctly.
How do you change the belt on a Nissan serpentine?
The last step is to slide the belt under the tensioner. Before you do that, make sure to check that the belt is properly seated on all the pulleys, or you will have a hard time sliding the new belt over the tensioner. Typical applications include:
Do you need to replace both belts on a Nissan Maxima?
Due to the way the belts are places on the crankshaft, you will need to take off the outer belt to access the inner belt. Because of this, some mechanics recommend replacing both belts at the same time. This guide is based on information for Nissan Maxima model years 1993 to 2004.
How do you remove tensioner from Nissan serpentine belt?
Release Tensioner. Use a 3/8″ ratchet to push the tensioner away (up) from the belt. To get to the tensioner, you will either remove the passenger wheel or drive the car up on rams. This will allow you to remove the plastic cover on the wheel well to access the tensioner.
How often should a Nissan Maxima be inspected?
Nissan Maxima models older than 1995 had three separate belts and 1995 and up models have two belts. Due to normal wear on these belts, Nissan recommends inspection every 6000 miles or 6 months.
Tighten up the adjustment bolt to replace appropriate tension on the belt. Make sure the belt is seated on all pulleys. Tighten the lock bolt. Run the engine and observe to see if the belt is installed correctly.
Where is the tensioner on a Nissan Maxima?
The tensioner on the Maxima is tightened or loosened with a set of 14mm bolts on the side of the unit. Raise the hood and use the flashlight to locate the tensioner. It is near the rear exhaust manifold and has two bolt heads below the pulley. Loosen the locking nut using the 14mm socket, universal socket adapter, extension and wrench.
What kind of drive system does Nissan Maxima have?
The Nissan Maxima is equipped with a serpentine drive system that transfers torque from the crankshaft pulley to the various engine accessories such as the alternator, power steering pump and air-conditioning compressor. The belt that transfers this energy must be held in place with a belt tensioner,…
How much does a belt tensioner for a Nissan Maxima cost?
The best part is, our Nissan Maxima Belt Tensioner Assembly products start from as little as $43.29. When it comes to your Nissan Maxima, you want parts and products from only trusted brands.
How is the belt held in place on a maxima?
The belt that transfers this energy must be held in place with a belt tensioner, a moveable device with an idler pulley that pushes the belt into place, holding it taut so that it does not fly off the engine. The tensioner on the Maxima is tightened or loosened with a set of 14mm bolts on the side of the unit.
What to do if your drive belt tensioner is faulty?
Remove the drive belt (s) (in most cases). Inspect drive belt pulleys. Check the drive belt tensioner. Remove and replace the tensioner if faulty. Start car to see if noise is gone. Your drive belt tensioner should always be inspected when your drive belt is serviced.
What kind of pulley does a Nissan Maxima use?
Use the fitment form at the top of the page to select your exact year and engine type for your Nissan Maxima. Manufactured by one of the world’s largest Original Equipment supplier of accessory drive tensioners and pulleys. Heavy Duty Steel Pulley with close tolerance ball bearing pocket. 6203 bearing. I highly recommend this part.