How do you replace the wheel studs on a Honda?
Set the car on four jack stands. Remove the wheel and the axle nut. Then, remove the rotor nuts and the caliper. Set the caliper where it won’t hang from the brake hose. Remove the rotor. Figure 1. Removing the rotor. Remove the lug nuts.
What are the studs on a Honda Civic?
This article applies to the Honda Civic (1992-2000), and Accord (1990-2002). The wheel studs are what hold your wheel to the car. It’s not uncommon for studs to wear down or break over time, and losing one isn’t the end of the world. But you still want all four intact to ensure that your wheels won’t just fall off.
What are the studs on a car wheel?
The wheel studs are what hold your wheel to the car. It’s not uncommon for studs to wear down or break over time, and losing one isn’t the end of the world. But you still want all four intact to ensure that your wheels won’t just fall off.
Set the car on four jack stands. Remove the wheel and the axle nut. Then, remove the rotor nuts and the caliper. Set the caliper where it won’t hang from the brake hose. Remove the rotor. Figure 1. Removing the rotor. Remove the lug nuts.
This article applies to the Honda Civic (1992-2000), and Accord (1990-2002). The wheel studs are what hold your wheel to the car. It’s not uncommon for studs to wear down or break over time, and losing one isn’t the end of the world. But you still want all four intact to ensure that your wheels won’t just fall off.
The wheel studs are what hold your wheel to the car. It’s not uncommon for studs to wear down or break over time, and losing one isn’t the end of the world. But you still want all four intact to ensure that your wheels won’t just fall off.
How to remove the rear drive shaft on a Honda ATV?
I always pull the joint off the rear of the motor, rather than try to pull the shaft out of the joint. Take a flat blade screwdriver and pry it off the output shaft coming out of the motor. I got it thanks.
Is there a way to remove the rear driveshaft?
Pulling my engine (see other thread) – down to the step of removing the rear driveshaft & it should pop right out. I’m following what’s described in the attached picture; however, only thing that’s came loose so far is the wrong end!
How to replace the lug studs in a CRV?
A professional kit has a nice bearing unit instead of using washers but done the same way on about any car. Beat the old stud back a bit so you can cut the head off and pull the rest out. Grind the new stud head as he did and pull the new one in with the washers between the nut and the hub.
Can a wheel bearing race be removed from a CRV?
Not just a CRV issue, very common across many vehicles. To add to the above, when the hub is pulled out, the wheel bearing race comes with it…so the job also becomes replacing a wheel bearing + removing the race from the hub if you want to re-use it.
How do you remove the hub from an axle puller?
Remove the lug nuts. Put the axle puller over the studs, and tighten it down using the lug nuts. Then attach the slide hammer to the axle puller. To remove the hub, repeatedly pull back on the heavy handle with straight and steady strokes. When you think the hub is about to give make sure that it doesn’t hit the ground hard.
Remove the lug nuts. Put the axle puller over the studs, and tighten it down using the lug nuts. Then attach the slide hammer to the axle puller. To remove the hub, repeatedly pull back on the heavy handle with straight and steady strokes. When you think the hub is about to give make sure that it doesn’t hit the ground hard.
A professional kit has a nice bearing unit instead of using washers but done the same way on about any car. Beat the old stud back a bit so you can cut the head off and pull the rest out. Grind the new stud head as he did and pull the new one in with the washers between the nut and the hub.
How to replace the hub on a Honda?
Pull all the brake hardware off and tie it out of the way. Get the old stud out, may need to grind it close to hub so it can be punched out. Use a dremel to cut a slice in the dust cover so you can peel it back out of the way a bit like shown in the picture. Do this at the flattest part of the knuckle.
Pull all the brake hardware off and tie it out of the way. Get the old stud out, may need to grind it close to hub so it can be punched out. Use a dremel to cut a slice in the dust cover so you can peel it back out of the way a bit like shown in the picture. Do this at the flattest part of the knuckle.
What’s the best way to replace a Honda Accord?
With the hub pulled, now is the perfect time to give the wheel bearings and axle ends a little TLC. If they are rusty, get some 800-grit sandpaper and get rid of as much rust as possible. Once that is cleaned up, use some multi-purpose grease and lube the wheel bearing, axle, and housing.
How do you replace the spindle nut on a Honda Accord?
Put the spindle nut back on and use a screwdriver to deform it back into the void part of the drive shaft. Tighten down the spindle nut to at least where the end of the shaft meets the end of the spindle nut. Actual specifications call for about 181 foot-pounds of torque.
How do you replace a broken lug nut stud?
Use your fingers to pull the broken bolt from the rear of the hub flange. The replacement bolt was a stock part from a local auto parts supplier. To install the new bolt into the bolt hole, the wheel must be turned to align the hole with a slot on the rear of the hub flange, which provides the clearance to thread it through.
How do you take stud out of Honda front wheel?
Get the old stud out, may need to grind it close to hub so it can be punched out. Use a dremel to cut a slice in the dust cover so you can peel it back out of the way a bit like shown in the picture. Do this at the flattest part of the knuckle.
Is it possible to replace front wheel studs?
So, yes it is possible to replace the front wheel studs without pulling the hub and messing up your wheel bearing. If you want to go the “pull the hub route”, there’s a good thread on it here. http://www.odyclub.com/forums/24-1999-2004-odyssey/32049-wheel-stud-replacement-w-pics.html
What’s the best way to replace a Honda wheel?
Put the hub back on the spindle. Then reattach the hub puller, and slide the hammer. Hit the hub back on starting slowly and working your way up to steady strokes. Put the axle nut back on, and torque it to 134 lb/ft. Figure 5. Attach the hub, rotor, and caliper.