What kind of engine does an Altima have?
The most recent version of the Altima was the 2011 series, with torque specifications varying over four models. The 2.5 and 2.5 S model Altimas were both outfitted with a 2.5-liter, 16-valve, four-cylinder engine capable of producing 180 ft.-lb. of torque at 3,900 rpm.
What kind of torque does a Nissan Maxima have?
TORQUE SPECIFICATIONS NISSAN APPLICATION FT-LBS (N-m) AXLE SPINDLE NUT 1986-78 115 (157) 1994-87 ALTIMA, MAXIMA, STANZA, & QUEST 174-232 (237-316) PULSAR, SENTRA, 240SX, & 300ZX 145-203 (197-276) AXLE SHAFT-TO-SIDE FLANGE NUT 240SX & 300ZX NON-TURBO 25-33 (34-44) 300ZX TURBO (BOLT) 51-58 (68-78)
What kind of lug nut does Nissan Altima have?
Here is a list of lug nut torque specs and sizes for a Nissan Altima. Reference the model year in the table to see what lug nut torque and size is applicable for your car.
When did the Nissan Altima come out in the US?
Developed and manufactured by the Nissan Motor Company, the Altima was first released in the United States in 1993. A competitor to Honda’s Accord and Toyota’s Camry, the Altima was available for purchase in coupe and sedan styles, and with a hybrid engine.
APPLIED VEHICLES: 2013-2016 Altima (L33) with 4-cyl engine only 2014-2016 Rogue (T32) NOTE: Does not apply to Rogue Select (S35) IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration),
How to update ASIST on a Nissan Altima?
Once all ASIST and CONSULT related updates have been performed, attach the CONSULT PC to the vehicle. Connect the plus VI to the vehicle. Connect the AC adapter to the CONSULT PC. 3. Turn ON the CONSULT PC, and then open CONSULT III plus (C-III plus).
How to read engine OBDII Codes without Nissan scan tool?
In this way, all the detected malfunctions are classified by their DTC numbers. The DTC 0000 refers to no malfunction. How to read the engine codes without a Nissan CONSULT or scan tool. (Set ECM in Diagnostic Test Mode II) Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
When to replace the CVT Assembly on an Altima?
If P17F0 is stored, replace the CVT assembly. For CVT assembly pre-approval, refer to page 23, Component Replacement Approval Procedures. Refer to the appropriate Electronic Service Manual (ESM), section TM-Transaxle & Transmission, for CVT assembly replacement procedure.
What’s the death code for a Nissan Altima?
P1778 got you down? About 6 months ago I received the death code P1778 (stepper motor) in my 2008 Altima.
What to do when your Nissan P1778 Got you Down?
7)take a piece of dental floss about a foot long and hold the spring loaded arm back against the stepper motor and return the valve body back to the transmission. 8)after you have a few bolts in place remove the floss before you tighten all the way.
In this way, all the detected malfunctions are classified by their DTC numbers. The DTC 0000 refers to no malfunction. How to read the engine codes without a Nissan CONSULT or scan tool. (Set ECM in Diagnostic Test Mode II) Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
What should I replace CVT fluid in Nissan P1778?
10)rejoin the fluid pan to the transmission and replace with quality cvt fluid. Amsoil makes a great product. I hope this helps and if you have questions please feel free to ask. Well done, you’ve shown that with the right amount of elbow grease, you can salvage what might otherwise have sent you looking for another car.