Where is the camshaft position sensor located on a Nissan Altima?
Nissan models with a distributor, the camshaft position sensor are part of the distributor. Code P0725 / P0335 / P0340 – Camshaft Positioning Sensor Replacement – Nissan Altima. If playback doesn’t begin shortly, try restarting your device.
What kind of oil does a Nissan Altima use?
Here is a list of engine oil types and capacities for a Nissan Altima. Reference the model year in the table with the corresponding engine to see what oil type and capacity is applicable for your car. SAE 5W-30 viscosity oil is preferred for all temperatures. SAE 10W-30 or 10W-40 viscosity oil may be SAE 5W-30 oil is preferred .
Is there a problem with the CVT transmission on a Nissan Altima?
Many people who owned the 2013 Nissan Altima started to notice Nissan CVT transmission problems at around the 53,000-mile mark and found that they cost around $3,100 to fix. It caused many Altima owners to second-guess their decision to buy Nissans and is at least partly to blame for Nissan’s current predicament.
What is the p0340 Nissan camshaft position sensor?
P0340 Nissan Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
Nissan models with a distributor, the camshaft position sensor are part of the distributor. Code P0725 / P0335 / P0340 – Camshaft Positioning Sensor Replacement – Nissan Altima. If playback doesn’t begin shortly, try restarting your device.
Is the camshaft position sensor part of the distributor?
Nissan models with distributor the camshaft position sensor is part of the distributor. There is a factory service bulletin for the following Nissan models: 2003 Nissan Altima. 2004 Nissan Altima. 2005 Nissan Altima. 2004 Nissan Quest. 2004 Nissan Maxima. Nissan Factory Service Bulletin OBDII Code P0340.
What causes a Nissan camshaft sensor to malfunction?
P0340 NISSAN Possible Causes 1 Faulty Camshaft Position Sensor 2 Camshaft Position Sensor harness is open or shorted 3 Camshaft Position Sensor circuit poor electrical connection 4 Faulty starter motor 5 Starting system circuit 6 Dead (Weak) battery
P0340 Nissan Description. The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module(ECM) to control ignition and fuel injection.
How is the camshaft position sensor used in an engine?
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module ( ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder.
How much does it cost to repair a Nissan camshaft sensor?
Nissan models with a distributor, the camshaft position sensor are part of the distributor. The cost of diagnosing the P0340 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
Where is the camshaft position sensor Nissan Frontier Pathfinder Xterra?
Step 1: Visually locate the sensor on the backside of the engine block. You can see the wiring harness coming out of the back of the sensor and a hex bolt head to the side of the sensor. It is located on the passenger side about ¼ of the way down the block. Step 2: Unhook hoses and wires to gain access to area.
Where is the camshaft position sensor located on a car?
The camshaft position sensor is located on the upper part of the timing chain cover. It’s right near where the timing chain cover meets the valve cover. The arrow in the photo above points to the camshaft position sensor location.
Nissan models with a distributor, the camshaft position sensor are part of the distributor. The cost of diagnosing the P0340 NISSAN code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
How to test the cam sensors ( 2002-2003 Nissan Maxima )?
The 2002-2003 3.5L Nissan Maxima has 2 camshaft position sensors and both can be easily tested with a multimeter. In this tutorial I’ll show you how in a step-by-step manner. Symptoms Of A Defective Camshaft Position Sensor.
Why do I need to change the camshaft position sensor?
The problem with changing out the camshaft position sensor is that sometimes the issue is actually due to the sensor wiring harness; which might be the reason this OBD-II error code was triggered initially. The P-0340 trouble code indicates that the signal to and from the camshaft position sensor and the PCM is broken.
P0340 NISSAN Possible Causes 1 Faulty Camshaft Position Sensor 2 Camshaft Position Sensor harness is open or shorted 3 Camshaft Position Sensor circuit poor electrical connection 4 Faulty starter motor 5 Starting system circuit 6 Dead (Weak) battery
When does the camshaft position sensor signal not detect?
The camshaft position sensor signal is not detected by the Engine Control Module(ECM) during the first few seconds of engine cranking P0340 NISSAN Possible Symptoms Engine Light ON (or Service Engine Soon Warning Light) Lack/Loss of Power Engine Stall P0340 Nissan Description
What causes a Nissan Altima engine to stall?
The engine may stall when the engine is warmed up. This can be caused by a failed crankshaft position sensor and/or camshaft position sensor. These sensors can fail intermittently so the problem may come and go. Sensors on certain models have been recalled by Nissan and will be replaced as necessary.
Nissan models with distributor the camshaft position sensor is part of the distributor. There is a factory service bulletin for the following Nissan models: 2003 Nissan Altima. 2004 Nissan Altima. 2005 Nissan Altima. 2004 Nissan Quest. 2004 Nissan Maxima. Nissan Factory Service Bulletin OBDII Code P0340.
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. This information is used by the Engine Control Module ( ECM) to control ignition and fuel injection. The camshaft position sensor senses the retraction of camshaft (intake) to identify a particular cylinder.