Why is the blower motor on my Nissan Altima not working?

Why is the blower motor on my Nissan Altima not working?

Unfortunately the blower motor on the Altima is not working. The Blower motor LED lights light up to high speed but no fan. I am no where near the car ( My wife has it far away ) but I’m wondering if it is a fuse or the motor?

Where is the blower motor on a Nissan?

Note the blower motor assembly behind the airbag harness — it is held in place with screws. Remove the blower motor assembly screws and pull the assembly out from the dashboard. As you pull the assembly out, disconnect the wiring that connects to the back of the assembly.

How much does it cost to replace heater resistor on Altima?

Nissan Altima Car Heater Blower Motor Resistor Replacement costs $181 on average. What is the Heater Blower Motor Resistor all about? The heater blower motor resistor is located underneath the dashboard in the heater/AC compartment. The resistor enables the heater blower motor to change the speed of the fan.

Where is the fuse on a blower motor?

the blower motor fuse is inside the car on the driver side lower dash. There is a little panel you can remove. This circuit takes 2 15 amp fuses, i learned my lesson when i blew both and only replaced one, and wondered why i kept blowing that fuse. The fuses will be listed on that little panel you take off.

Unfortunately the blower motor on the Altima is not working. The Blower motor LED lights light up to high speed but no fan. I am no where near the car ( My wife has it far away ) but I’m wondering if it is a fuse or the motor?

the blower motor fuse is inside the car on the driver side lower dash. There is a little panel you can remove. This circuit takes 2 15 amp fuses, i learned my lesson when i blew both and only replaced one, and wondered why i kept blowing that fuse. The fuses will be listed on that little panel you take off.

What are the fuses on a Nissan club blower?

There is a little panel you can remove. This circuit takes 2 15 amp fuses, i learned my lesson when i blew both and only replaced one, and wondered why i kept blowing that fuse. The fuses will be listed on that little panel you take off.

How does the Auto AC affect the blower motor?

In short, the blower motor is mounted in series with the fan control amp. The auto AC regulates the fan control amp, which regulates the voltage to the blower motor. A low speed setting causes a lower voltage across the blower motor, which makes the motor operate slower.

Where can I get a motor resistor replaced on my Altima?

Nissan Altima Car Heater Blower Motor Resistor Replacement at your home or office. Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing. Our certified mobile mechanics can come to Chicago, IL 7 days a week between 7 AM and 9 PM. received a Heater Blower Motor Resistor Replacement.

Where is the heater blower motor resistor located?

The heater blower motor resistor is located underneath the dashboard in the heater/AC compartment. The resistor enables the heater blower motor to change the speed of the fan.

What happens if the resistor on the blower goes bad?

The resistor enables the heater blower motor to change the speed of the fan. Without this part you will not be able to change the speed of the airflow from the blower motor. It is also possible that the heater motor blower may not work at all. If the resistor has gone bad, it is likely that the fan will work only on the highest speed.

How does a Nissan blower motor resistor work?

We offer a full selection of genuine Nissan Blower Motor Resistors, engineered specifically to restore factory performance. Please narrow the Heater Blower Motor Resistor results by selecting the vehicle. Simply, the blower motor pushes air through the vents.

Nissan Altima Car Heater Blower Motor Resistor Replacement at your home or office. Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing. Our certified mobile mechanics can come to Chicago, IL 7 days a week between 7 AM and 9 PM. received a Heater Blower Motor Resistor Replacement.

The heater blower motor resistor is located underneath the dashboard in the heater/AC compartment. The resistor enables the heater blower motor to change the speed of the fan.

In short, the blower motor is mounted in series with the fan control amp. The auto AC regulates the fan control amp, which regulates the voltage to the blower motor. A low speed setting causes a lower voltage across the blower motor, which makes the motor operate slower.

Why is the blower on my Nissan club not working?

Checked the two fuses, and they are both good. I can hear the AC compressor kick on if I lower the temp, but no air flow coming from the vents. Switching from defrost, floor, dash vents and no air flow. Manually adjusting the fan speed and still no air flow. It looks like there is a resistor plug that inserts into the blower assembly.

What causes a blower fan to not work?

When this happens, you may notice that you will not feel anything blowing out of the vents at all. This may also cause the blower motor to work intermittently. A blower fan is connected to the negative battery terminal (also called ground) on one end and to the positive battery terminal through a blower motor resistor on the other end.

What to do if your blower fan stops working?

Take glove box out on passenger side. Upper left corner is Blower Fan Knock on it. If it comes on it is going out will need to replace. Blower fan will not come on at all? Check Fuses & Blower Fan? Fuses replaced for blower fan,took blower fan out and tested it and it worked? Well it has to be you climate control panel nothing else to check!

What happens if the blower motor only works on high speed?

In other designs, the failure of 1 resistor means you lose only one speed. However, most car makers bypass the blower motor resistor completely when you move the fan speed switch to high. If your blower only operates on its highest speed, chances are you have the series type of blower motor resistor. This is the most common failure mode.

Why does my Ricks free auto blower motor not work?

A clogged cabin air filter reduces airflow through the ducts, increases current draw on the blower motor and can cause blower motor resistor overheating and premature failure. If you replace the resistor and it burns out again, check the current draw on the blower motor.

Where is the airbag harness on a Nissan blower?

Pinpoint the airbag harness connector in the space behind the glove box assembly. Use your hands to pull the connector´s wiring from its power source. Note the blower motor assembly behind the airbag harness — it is held in place with screws. Remove the blower motor assembly screws and pull the assembly out from the dashboard.

What to do if your Rogue blower goes bad?

If playback doesn’t begin shortly, try restarting your device. An error occurred. Please try again later. (Playback ID: rPVKNn2AqdmVpEjE) Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information.

What causes a bad or failing blower motor relay?

Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…

Is the blower motor the same as the fan control AMP?

Our version (at least for the auto control AC) is the Y33. The metal housing looks different, but the circuit board is the same with the same value components. In short, the blower motor is mounted in series with the fan control amp. The auto AC regulates the fan control amp, which regulates the voltage to the blower motor.

What are common reasons my Nissan Sentra has heater problems?

What are common reasons my Nissan Sentra has heater problems? While there are a variety of reasons your Nissan Sentra heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor.

Take glove box out on passenger side. Upper left corner is Blower Fan Knock on it. If it comes on it is going out will need to replace. Blower fan will not come on at all? Check Fuses & Blower Fan? Fuses replaced for blower fan,took blower fan out and tested it and it worked? Well it has to be you climate control panel nothing else to check!

What are common reasons my Nissan Sentra has heater problems? While there are a variety of reasons your Nissan Sentra heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor.

Checked the two fuses, and they are both good. I can hear the AC compressor kick on if I lower the temp, but no air flow coming from the vents. Switching from defrost, floor, dash vents and no air flow. Manually adjusting the fan speed and still no air flow. It looks like there is a resistor plug that inserts into the blower assembly.

Where is the blower relay on a Nissan Versa?

Blower relay is only used for speed 4 other 3 speeds run through the resistor unit. blower motor resistor block is actually in the air ducting near the blower motor.

What to do if Nissan Altima has no AC?

Prosses for checking for a bad AC clutch. Went from cold good cold AC to no Ac at all, so I don’t expect low pressure in this situation. AboutPressCopyrightContact usCreatorsAdvertiseDevelopersTermsPrivacyPolicy & SafetyHow YouTube worksTest new features

Why is there no air blowing out the vents?

As of Thursday morning, I have no air blowing out the vents. All the LED’s light up (automatic climate control) but there is no air flow when adjusting the speed of the fan. Fuses are good. I tried running the self-diagnostic and got an error–sunload circuit open, but it was cloudy and I don’t expect to see the sun until Wednesday to test again.

As of Thursday morning, I have no air blowing out the vents. All the LED’s light up (automatic climate control) but there is no air flow when adjusting the speed of the fan. Fuses are good. I tried running the self-diagnostic and got an error–sunload circuit open, but it was cloudy and I don’t expect to see the sun until Wednesday to test again.

Blower relay is only used for speed 4 other 3 speeds run through the resistor unit. blower motor resistor block is actually in the air ducting near the blower motor.

Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…

What causes a fuse to blow on a blower motor?

If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.

What happens if you have a bad blower motor?

The blower motor is the component responsible for pushing air through the vents of your vehicle’s heating and air conditioning systems. Without it, the AC system will not be able to circulate any heated or cooled air.

Can a blown fuse be replaced in a Nissan NV200?

Some components may have multiple fuses, so make sure you check all of the fuses that are linked to the component in question. If you need to replace a blown fuse in your NV200, make sure you replace it with one that has the same amperage as the blown fuse.

How does the heater work on a Nissan NV200?

At the simplest level possible, the heater works by passing hot coolant from the engine into a tiny radiator called the heater core. At this point, the blower motor blows air across the it and the newly heated air blows on to the driver and passengers. If the heater has stopped working in your NV200, this process has failed in one way or another.

Why does my blower motor run slower at low speed?

A low speed setting causes a lower voltage across the blower motor, which makes the motor operate slower. At maximum fan speed setting, the fan control amp allows nearly all 12v across the motor, which causes the fan to run faster.

What to do if your blower motor stops working?

Personally, I replaced mine when it stopped working and that solved the problem. There is a motor and relay below the motor that many folks replace at the same time, since both are known to fail. One form member even has an excellent write up about the replacement, including pics.

What happens if you lose the blower motor relay?

The blower motor is the component responsible for pushing air through the vents of your vehicle’s heating and air conditioning systems. Without it, the AC system will not be able to circulate any heated or cooled air. The blower motor relay controls the current used to power the blower motor,…

How long does it take to replace a Mercedes blower motor?

There is a motor and relay below the motor that many folks replace at the same time, since both are known to fail. One form member even has an excellent write up about the replacement, including pics. Very helpful! It’s about a 2-3 hour job, less if you’ve done one before. Thanks guys, I’ll look again. Must have missed it first time round

How to replace a blower resistor and motor?

Easy video on how to replace blower resistor and motor with 1 screw driver and in about 10min. Remove glove box, pop bottom panel off to gain motor access. Disconnect cables to motor and resistor. Remove hose from motor, it should just pull off with little effort. Unscrew motor and resistor. Screw new motor and resistor in. Connect hose to motor.

What to do if your AC blower is not working?

Disconnect cables to motor and resistor. Remove hose from motor, it should just pull off with little effort. Unscrew motor and resistor. Screw new motor and resistor in. Connect hose to motor. Connect cables to motor and resistor. Turn on car and test AC. Thanks for watching! Loading…

The blower motor is the component responsible for pushing air through the vents of your vehicle’s heating and air conditioning systems. Without it, the AC system will not be able to circulate any heated or cooled air. The blower motor relay controls the current used to power the blower motor,…

Where is the blower control switch on the dashboard?

The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.

Why is the blower motor not working on my car?

My car has an automatic transmission. Hi There, The resistor is what controls the speed of the blower motor, not the relay. The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all.

Where is the sun load sensor on a Nissan club?

The sun load sensor is located on the passenger side dash right near the bottom of the windshield and the resistor is near the blower motor. The connector pin outs confused me when I was troubleshooting another member’s car but I eventually figured out what pin outs the manual was talking about.

What does it mean if your blower motor is not working?

Average rating from 849 customers who received a AC is not working Inspection. The blower motor resistor is an electrical component that is a part of the vehicle’s heating and air conditioning system. It is responsible for controlling the blower motor’s fan speed.

When do you need to replace the blower motor relay?

If the blower motor does not function, car fuses are blown, or relays are melting, you may have to replace the car blower motor relay. 1. Blower motor does not function 2. Blown fuses 3. Melted relay The blower motor relay is the electrical switch that is used to supply the power for the vehicle’s blower motor.

How do you check the fuse on a Nissan Altima?

Open the fuse box lid. On the fuse diagram, find the number of the fuse you want to check. The diagram tells you where to locate the fuse on the panel. Pinch the fuse perpendicularly with the fuse puller and pull it out. To check a fuse, look at the silver-colored band inside the fuse.

There is a little panel you can remove. This circuit takes 2 15 amp fuses, i learned my lesson when i blew both and only replaced one, and wondered why i kept blowing that fuse. The fuses will be listed on that little panel you take off.

If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current from a bad relay will blow the fuse and cut power in order to protect the system.

What should I do if my Nissan Altima fuse is not working?

If a new fuse also opens, have the electrical system checked and repaired by a Nissan dealer or a repair facility of your choice. If any electrical equipment does not operate and fuses are in good condition, check the fusible links. Never use a fuse of a higher or lower amperage rating than that specified.

If a new fuse also opens, have the electrical system checked and repaired by a Nissan dealer or a repair facility of your choice. If any electrical equipment does not operate and fuses are in good condition, check the fusible links. Never use a fuse of a higher or lower amperage rating than that specified.

When this happens, you may notice that you will not feel anything blowing out of the vents at all. This may also cause the blower motor to work intermittently. A blower fan is connected to the negative battery terminal (also called ground) on one end and to the positive battery terminal through a blower motor resistor on the other end.

How does a high speed blower motor work?

In the highest fan speed state, the blower resistor is bypassed completely and the fan is effectively connected directly to the car’s battery, allowing maximum current to be supplied to the blower motor.

What to do if your radiator fan is not working?

The first thing that you would want to do is locate the fuse for your Altima’s radiator fan and make sure that it hasn’t blown. If it is blown, replacing the fuse will only solve the problem for a very limited period of time. Unless the wiring issue is fixed, the fuse will blow again.

What to do if your Altima has a bad temp sensor?

If your Altima has a bad engine temp sensor the radiator fan won’t know to come on, because the ECU won’t know how hot the engine is. You’ll need to locate and test the engine temp sensor. Depending on the model year and engine, the location varies. If it does end up being this sensor, they are very affordable.

What are common reasons my Nissan Altima has heater problems?

What are common reasons my Nissan Altima has heater problems? While there are a variety of reasons your Nissan Altima heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor. See what others are asking about their Nissan Altima.

If your Altima has a bad engine temp sensor the radiator fan won’t know to come on, because the ECU won’t know how hot the engine is. You’ll need to locate and test the engine temp sensor. Depending on the model year and engine, the location varies. If it does end up being this sensor, they are very affordable.

Why is my radiator fan not working on my Toyota Camry?

If you do have low coolant, don’t fill it up until the engine has cooled off. Adding coolant to a radiator dry enough not to trigger the engine temp sensor can cause problems from drastic temperature change. Let it cool down first. Like any other clutch, a fan clutch will wear out over time.

What happens when the blower fails on a Chevy Equinox?

When the blower motor fails, the air conditioner and heater may still work, and heat or cool may be felt at the vents, but the air pressure will be dramatically decreased. This Read More When the heater control valve fails, adjusting the temperature may not change the air temperature at the vents, whether hot or cold.

Why does my Acura heater smell like engine coolant?

A failing heater core may cause the car’s interior to smell like engine coolant. The smell will become worse when the heater is turned on. The engine may also begin to run hotte…

What causes a Nissan Altima to lose power?

The power loss failure can be related to a damaged catalytic converter, which is a manufacturing problem that car model has. You can try removing the converter and your problem should be solved. Good luck. Altima cars have got oil pump and camshaft manufacturing problems.

Can a Nissan blower fan be replaced without removing the dashboard?

The blower motor fan may need replacement. I will show you how you can replace your Nissan Blower Motor without removing the dashboard. Disclaimers: all opinions are my own, sponsors are acknowledged. Links in the description are typically affiliate links that let you help support the channel at no extra cost. Loading…

Why does my AC Heat fan make a clicking noise?

If your interior AC/ Heat fan (blower motor) is making noise like a card in a bicycle spoke, then you probably just need to clean out the blower motor which is easy and free. Leaves and debris gets in the blower motor and make a clicking noise when the fan hits the leaves.

What should I do if my car fuse keeps blowing?

The important thing is to understand what is causing the fuse to keep blowing. The simple fix is often replacing the blown fuse and test the car again. If the fuse does not blow, it might be an easy fix because there was a power surge in the system.

What causes a blower motor to run faster?

At maximum fan speed setting, the fan control amp allows nearly all 12v across the motor, which causes the fan to run faster. Not sure how much one of these fan control amps cost new or from a junkyard, but mine was a simple fix since it was just the temperture cutout had blown.

What to do if your Nissan Maxima heater is not working?

Actual prices may change depending on final diagnosis. Nissan Maxima Heater Is Not Working Repair Symptoms. When the blower motor fails, the air conditioner and heater may still work, and heat or cool may be felt at the vents, but the air pressure will be dramatically decreased.

The blower motor fan may need replacement. I will show you how you can replace your Nissan Blower Motor without removing the dashboard. Disclaimers: all opinions are my own, sponsors are acknowledged. Links in the description are typically affiliate links that let you help support the channel at no extra cost. Loading…

Where is the relay on a Nissan fan?

Relay is located at the fuse block on driver-side, remove plastic door on top of hood release latch. Switch relay with another relay and see if it works. Since my car manual did not show a way to test the resistor, I decided to replace the resistor and that fixed the problem.

Relay is located at the fuse block on driver-side, remove plastic door on top of hood release latch. Switch relay with another relay and see if it works. Since my car manual did not show a way to test the resistor, I decided to replace the resistor and that fixed the problem.

On the fuse diagram, find the number of the fuse you want to check. The diagram tells you where to locate the fuse on the panel. Pinch the fuse perpendicularly with the fuse puller and pull it out. To check a fuse, look at the silver-colored band inside the fuse.

Why does my Nissan 350Z have a blown fuse?

Fuses and fusible links protect your vehicle’s electrical system from short-circuiting or overloading. If electrical parts in your vehicle are not working, the system may have been overloaded causing a blown fuse. Before you replace or repair any electrical parts, check the appropriate fuses.

Why is my Nissan Note heater not working?

When I removed the unit I discovered it was “VALEO”so we googled the part no.F667165W/R &discovered it is fitted to a PEUGEOT 406 with aircon 92>.Rang my cousin who works in a scrapyard 20euro &1/2 hour later we have a blower again.Will try to put some pics.of it up here. would come on and off as if i had a loose connection.

Disconnect cables to motor and resistor. Remove hose from motor, it should just pull off with little effort. Unscrew motor and resistor. Screw new motor and resistor in. Connect hose to motor. Connect cables to motor and resistor. Turn on car and test AC. Thanks for watching! Loading…

What are the symptoms of a failed blower motor resistor?

Blower motor resistor problems. Problems with a blower motor resistor are common in many cars. The most common symptom of a failed blower motor resistor is when the heater fan only runs at high speed and doesn’t work at low speeds.

What to do if your AC Fan is not working?

The fan under the hood can be checked as follows: 1. Play it safe and disconnect the battery + / – wire to prevent possible electrical damage — just in case a mistake is made. 2. Disconnect the fan wire at one of it’s wiring connections 3. Connect wire directly from the fan’s wiring connection to the battery. If the fan motor is good it will run.

Why is my blower motor stuck on one speed?

Blower motor stuck on one speed A common symptom of a faulty blower motor resistor is a blower motor that is stuck on one setting. The blower motor resistor is the component directly responsible for controlling the blower motor fan speed. If the resistor shorts or fails, it may cause the blower motor to remain stuck on one fan speed.

The blower control switch on the dashboard controls the circuit flow of the blower motor to adjust the voltage from low, to medium, to medium-high, to high. When on high, the circuit bypasses the blower resistor.

A low speed setting causes a lower voltage across the blower motor, which makes the motor operate slower. At maximum fan speed setting, the fan control amp allows nearly all 12v across the motor, which causes the fan to run faster.

Why is the radiator not working on my Nissan Altima?

If the radiator fan is not working, it’s a serious problem. Just because the radiator fan is not on does not mean that it is not working. They are designed to only run when needed. If your Altima is running hot, and the fan is not running we’ve laid out the most common causes of this issue below.

The first thing that you would want to do is locate the fuse for your Altima’s radiator fan and make sure that it hasn’t blown. If it is blown, replacing the fuse will only solve the problem for a very limited period of time. Unless the wiring issue is fixed, the fuse will blow again.

What are common reasons my Nissan Maxima has heater problems?

What are common reasons my Nissan Maxima has heater problems? While there are a variety of reasons your Nissan Maxima heater is not working, the most common 3 are a broken heater blower motor, a problem with the thermostat, or a failed heater blower motor resistor. See what others are asking about their Nissan Maxima.

What to do if your Altima won’t start?

Videos you watch may be added to the TV’s watch history and influence TV recommendations. To avoid this, cancel and sign in to YouTube on your computer. An error occurred while retrieving sharing information. Please try again later. Click here to read the blog.

What causes a Nissan blower motor to run slower?

The auto AC regulates the fan control amp, which regulates the voltage to the blower motor. A low speed setting causes a lower voltage across the blower motor, which makes the motor operate slower. At maximum fan speed setting, the fan control amp allows nearly all 12v across the motor, which causes the fan to run faster.

What are the symptoms of a bad air flow sensor?

The symptoms of a bad mass air flow sensor include low engine power, poor fuel economy, an engine that won’t start, a check engine light on the dash and a gas smell from the exhaust fumes. A bad mass air flow sensor is often the likely culprit if your car isn’t running as it should.

The blower motor is the component responsible for pushing air through the vents of your vehicle’s heating and air conditioning systems. Without it, the AC system will not be able to circulate any heated or cooled air.

Where is the EVAP canister on a Nissan Altima?

EVAP Canister Purge Volume Control Solenoid Valve, EVAP Canister Vent Control Valve, Intake Valve Timing Control Solenoid Valve (VK35DE), VIAS Control Solenoid Valve (VK35DE) It is near the battery. Remove the fuse box cover by pushing the tab and lifting the cover up.

Where is the blower motor relay on a Nissan Altima?

For the 2007 Altima, the blower motor relay is the farthest to the left blue fuse. When you pull it out, remember the position it was in – that way you don’t have to take the entire assembly out. 9. Put everything back in reverse order. Hope that helps.

Nissan Altima Car Heater Blower Motor Resistor Replacement costs $181 on average. What is the Heater Blower Motor Resistor all about? The heater blower motor resistor is located underneath the dashboard in the heater/AC compartment. The resistor enables the heater blower motor to change the speed of the fan.

What are the parts of a blower motor relay?

Instrument panel, blower motor. Coupe, instrument panel, accesory. Fuse & relay components, instrument panel, type 2. Engine compartment, engine room harness, cooling fan. WARNING: May cause cancer and reproductive harm. See www.P65Warnings.ca.gov for more info. providers are experiencing delays due to heavy volume and service disruptions.

Where are the fuses on a Nissan Maxima?

Fuse box diagram (fuse layout), location, and assignment of fuses Nissan Maxima and Maxima QX (A33) (1999, 2000, 2001, 2002, 2003) Fuses and fusible links protect your vehicle’s electrical system from short-circuiting or overloading. If electrical parts in your vehicle are not working, the system may have been overloaded causing a blown fuse.

Fuse box diagram (fuse layout), location, and assignment of fuses Nissan Maxima and Maxima QX (A33) (1999, 2000, 2001, 2002, 2003) Fuses and fusible links protect your vehicle’s electrical system from short-circuiting or overloading. If electrical parts in your vehicle are not working, the system may have been overloaded causing a blown fuse.

Where is the fuse box on a Nissan Altima?

Cigar lighter / power outlet fuses in the Nissan Altima are the fuses #5 and #18 in the Instrument panel fuse box. The fuse box is located behind the cover below and to the left of the steering wheel.

What kind of system does Nissan Altima have?

Headlamp, Intelligent Key System, Combination Meter, NVIS, Tire Pressure Monitoring System, Turn Signal and Hazard Warning Lamps, Vehicle Security System, Warning Chime, CVT Control System

When did the fourth generation Nissan Altima come out?

In this article, we consider the fourth-generation Nissan Altima (L32, D32), produced from 2007 to 2013. Here you will find fuse box diagrams of Nissan Altima 2007, 2008, 2009, 2010, 2011, 2012 and 2013, get information about the location of the fuse panels inside the car, and learn about the assignment of each fuse (fuse layout).

What happens when a blower motor relay wears out?

Without it, the AC system will not be able to circulate any heated or cooled air. The blower motor relay controls the current used to power the blower motor, and is subject to the constant on and off switching. Over time, it can eventually wear out.

Where is the a / C control relay located?

The A/C compressor relay is located inside the IPDM and is not serviceable you will need to replace the unit. Check out the diagrams (Below). Please let us know if you need anything else to get the problem fixed.

Why does my Almera have no heater fan?

Their fault appears to be fan only running on full speed but dads has no fan at all. If its out on all 4 speeds check the fuse. Also check to make sure tbe connector to the motor hasnt been kicked loose (its above the passenger footwell, unlikely but worth a look). It that fails it could be the motor itself. Thanks for the responses.

Where is the relay for the blower motor?

The blower motor relay could be possibly bad. Relay is located at the fuse block on driver-side, remove plastic door on top of hood release latch. Switch relay with another relay and see if it works. Since my car manual did not show a way to test the resistor, I decided to replace the resistor and that fixed the problem.

Their fault appears to be fan only running on full speed but dads has no fan at all. If its out on all 4 speeds check the fuse. Also check to make sure tbe connector to the motor hasnt been kicked loose (its above the passenger footwell, unlikely but worth a look). It that fails it could be the motor itself. Thanks for the responses.

How much does it cost to fix Almera heater resistor?

Put current across the motor terminals and it span. Couldn’t find the blower resister – took it to local garage (all makes) tested and declared resister failure. Just get it and fit. – MISTAKE. Charged £75.65 plus vat for part, 45 minutes to fit, plus “sundries” – £3.00.

Is there a problem with my fathers Almera?

Hope someone can give me advise on a problem with my fathers Almera 1.8 2002. He has had this car from new when he retired and has not had one problem with it. I caught him driving it yesterday with the windscreen completely fogged up. Driving one hand on wheel chamois leather in other.