Where is the blower motor on a 1992 Honda Accord?
Remove the glove box from the dashboard. The blower motor in the 1992 Accord is located behind the glove box inside the dashboard. Removing the glove box is the easiest way to access the blower motor. Insert a flat head screwdriver between the blower motor and the small vent tube protruding from the motor.
What kind of engine does a 1992 Honda Accord have?
The 1992 Honda Accord is equipped with a 2.2-liter, 125-horsepower, four-cylinder engine. The blower motor in the Honda Accord controls the flow of air through the heating and cooling system of the vehicle. The blower motor is usually removed for replacement or to clean the blower motor’s fan cage.
Where is the power transistor on a Honda Civic?
Disconnect the blower motor resistor (power transistor) from its harness connector. The power transistor is located under the right side (passenger side) of the dash. IMPORTANT: Before continuing on to the next steps, verify that your Honda Civic’s ignition switch is in the Off position.
Where is the heater duct on a Honda Accord?
The heater duct is located on the left side of the blower motor assembly. Figure 2. Remove self-taping screws holding heater duct in place. Remove the passenger’s side floor mat. Turn over the passenger’s side carpet, and pull it back as far as you can without tearing it.
Remove the glove box from the dashboard. The blower motor in the 1992 Accord is located behind the glove box inside the dashboard. Removing the glove box is the easiest way to access the blower motor. Insert a flat head screwdriver between the blower motor and the small vent tube protruding from the motor.
The 1992 Honda Accord is equipped with a 2.2-liter, 125-horsepower, four-cylinder engine. The blower motor in the Honda Accord controls the flow of air through the heating and cooling system of the vehicle. The blower motor is usually removed for replacement or to clean the blower motor’s fan cage.
When did the first Honda Accord come out?
The first Honda Accord was introduced in 1976 as a three-door hatchback. The Accord sedan was not released until 1979.
How do you remove a heater from a blower?
Set aside the cover. Unplug the plug on the top left of the blower motor assembly. Use the Phillips screwdriver or 10mm deep socket ratchet and extension to remove the metal band holding the blower assembly to the heater assembly. This connection is on the left side of the blower assembly. Set aside the metal band.
When did the Honda Accord blower motor come out?
How to Replace the Blower Motor in a 1992 Honda Accord. The first Honda Accord was introduced in 1976 as a three-door hatchback. The Accord sedan was not released until 1979. The Honda Accord was the first Japanese car ever to be produced in the United States. The 1992 Honda Accord is equipped with a 2.2-liter, 125-horsepower, four-cylinder engine.
How to replace the blower bracket on a Honda Accord?
Use 10mm deep socket ratchet and extension to remove the four nuts holding the ECU bracket (which is a large silver plate) in place. There are two nuts on top of the bracket, and there are two nuts on the bottom of the bracket. After removing the nuts, remove the bracket.
The heater duct is located on the left side of the blower motor assembly. Figure 2. Remove self-taping screws holding heater duct in place. Remove the passenger’s side floor mat. Turn over the passenger’s side carpet, and pull it back as far as you can without tearing it.
Why does my Honda Accord blower keep blowing out?
If you hear the blower motor assembly engage, but there is no air coming from your vents, then the problem is likely related to the airflow controls and not to the blower motor assembly. Before replacing your blower motor assembly, check the fuse to make sure it hasn’t blown out.
Set aside the cover. Unplug the plug on the top left of the blower motor assembly. Use the Phillips screwdriver or 10mm deep socket ratchet and extension to remove the metal band holding the blower assembly to the heater assembly. This connection is on the left side of the blower assembly. Set aside the metal band.
How do you remove the ECU from a blower?
Use the 10mm deep docket ratchet and extension to remove the three nuts holding the ECU to the bracket, and then unplug the ECU. Use the Phillips screwdriver to remove the two screws under the cover on the bottom of the blower.
The first Honda Accord was introduced in 1976 as a three-door hatchback. The Accord sedan was not released until 1979.
How do you remove the cover from a blower?
Use the Phillips screwdriver to remove the two screws under the cover on the bottom of the blower. Set the cover aside. Use the needle nose pliers or flat head screwdriver to remove the cover on the front of the blower assembly. To do this, you must remove the tiny clip holding the cover in place.
How to replace the blower motor assembly on a Honda Accord?
Before replacing your blower motor assembly, check the fuse to make sure it hasn’t blown out. Your owner’s manual will have information about which fuse controls the blower motor assembly.