How do you change a headlight on a 2001 Toyota Highlander?
Remove the Burned Out Bulb
- Pop the Hood open and use the support rod.
- Locate the burned out bulb.
- Remove the bulb by rotating it counter-clockwise and pulling it out of the housing.
- Disconnect the old bulb from the wiring connector.
- Install the new bulb into the connector.
How do you change the light bulb on a Toyota Highlander?
Open the back door and remove the 2 screws, and remove the lamp assembly by pulling it directly backward from the rear of the vehicle. Remove the wire harness. Turn the bulb base counterclockwise. Remove the light bulb. When installing the light bulb, install by conducting 4, 3 and 2 with the directions reversed.
How to install fog lights on a Toyota Highlander?
Front side marker lights Remove the 2 clips and remove the side cover. Turn the bulb base counterclockwise. Remove the light bulb. Install by conducting 2 and 3 with the directions reversed. Install the side cover and then install the 2 clips. Front fog lights (if equipped) Remove the 3 screws and partly remove the fender liner.
How do you install a light bulb base?
Turn the bulb base counterclockwise. Unplug the connector while pressing the lock release. Replace the light bulb, and install the bulb base. Align the 3 tabs on the light bulb with the mounting, and insert. Turn and secure the bulb base.
How do you change the license plate light?
License plate lights Remove the lens. Insert a properly sized screwdriver into the hole of the lens on the inner side and disengage the claw and pry the lens toward the outer side as shown in the illustration. To prevent damaging the vehicle, wrap the tip of the screwdriver with tape. Remove the light bulb.
Open the back door and remove the 2 screws, and remove the lamp assembly by pulling it directly backward from the rear of the vehicle. Remove the wire harness. Turn the bulb base counterclockwise. Remove the light bulb. When installing the light bulb, install by conducting 4, 3 and 2 with the directions reversed.
Front side marker lights Remove the 2 clips and remove the side cover. Turn the bulb base counterclockwise. Remove the light bulb. Install by conducting 2 and 3 with the directions reversed. Install the side cover and then install the 2 clips. Front fog lights (if equipped) Remove the 3 screws and partly remove the fender liner.
Turn the bulb base counterclockwise. Unplug the connector while pressing the lock release. Replace the light bulb, and install the bulb base. Align the 3 tabs on the light bulb with the mounting, and insert. Turn and secure the bulb base.
License plate lights Remove the lens. Insert a properly sized screwdriver into the hole of the lens on the inner side and disengage the claw and pry the lens toward the outer side as shown in the illustration. To prevent damaging the vehicle, wrap the tip of the screwdriver with tape. Remove the light bulb.
How much does it cost to get headlights replaced?
The Best in Auto Repair The average cost for headlight bulb replacement is between $109 and $130. Labor costs are estimated between $41 and $51 while parts are priced between $69 and $79. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.
Where is the headlight adjustment wheel on a Toyota Highlander?
Open the hood and locate the headlight adjustment wheel. Toyota places these near the headlight housing. Toyota doesn’t include a horizontal adjustment wheel, so if you need to adjust the horizontal trajectory, you either need to repair any damage to the frame or shim the headlight assembly.
How to adjust the aim on a Toyota Highlander?
Place the vehicle on a level surface. Bounce the vehicle up and down to settle the suspension. NOTICE: A distance of 7.62 m (25 ft) between the vehicle and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft) for check and adjustment.
Where is the H line on a Toyota Highlander?
The H line should be at the same height as the headlamp bulb center marks of the low-beam headlamps. V LH Line, V RH Line (Center mark position of lefthand (LH) and right-hand (RH) headlamps): Draw two vertical lines so that they intersect the H Line at each center mark (aligned with the center of the low-beam headlamp bulbs).
What’s the service manual for a Toyota Highlander?
Fill the fuel tank. Make sure that the oil is filled to the specified level. Make sure that the coolant is filled to the specified level. Inflate the tires to the appropriate pressure. Place the spare tire, tools, and jack in their original position. Unload the trunk. Sit a person of average weight (68 kg, 150 lbs) in the driver’s seat.