How to fix a 2009 SEA DOO RXT?

Loosen and remove the 8 bolts and raise the rear suspension arm. Take a long tie rap and secure it to the rear seat handrail. Raise the rear of the movable deck up to a distance of 340mm between movable deck and ski with a lifting strap. Remove all the screws holding the engine cowling and slide it out the back.

What should I do if my Sea Doo engine is not working?

Defective engine cut-off switch: Refer to an authorized Sea-Doo dealer. Dealer or repair shop. Watercraft is upside down. Turn watercraft upright! Engine management system fault: Seek service from an authorized Sea-Doo dealer or repair shop. iBR system fault: Refer to an authorized Sea-Doo dealer. Low fuel level: Refill fuel tank.

What to do when you need to replace the TPS on a Sea Doo?

Apply few drops of an anti-stick dielectrical grease to the tip of the replacement throttle sensor and install it in the throttle chamber. The anti-stick solution will make it easy for you to remove the TPS in case you need to replace it. Start the engine after connecting the throttle sensor harness connectors as specified in the shop manual.

Is the Sea Doo fault code on the dashboard?

Beware that unlike fault messages and indicator lights, Sea-Doo fault codes aren’t displayed on the dashboard. But don’t worry, the system warns you in case of any malfunction with beeps and fault messages, and at the same time it records a fault code. You can read the Sea-Doo fault codes with the B.U.D.S (BRP Utility and Diagnostic Software).

How to check throttle resistance on Sea Doo?

You need to disconnect the throttle sensor harness. Open the throttle valve manually and check the resistance between the terminal 1 and 2 changes. Check the resistance in three different positions of the accelerator pedal.

How to remove the suspension from a seadoo?

LOVE SeaDoo, but have no desire for the Suspension. At any rate, I can look up how to remove it, but I am at 34,000 feet right now. Internet is good, but not good enough to download PDF Files.. Open the front storage compartment and Remove the front storage compartment. Place a board (4×4) between the nose of the movable deck and the ski.

What’s the name of the new Sea Doo boat?

The new, yellow Sea-Doo RXT iS 255 from the Bombardier Recreation Products company (BRP) fits the bill, but performs more like those flying insects you see on the V energy drink commercial.

Why does my RTX X have 255 hp?

Could be a corroded fuse, loose connection or something simple. Maybe start in the two fuel boxes mounted to the battery box and look for corrosion. Then maybe check out the sensors on the air intake for loose wires, bad connection etc. 2009 RTX X (255 hp supercharged / inter-cooled). Remove the SC hoses and look to see if there is oil in them.

What are the problems with the Sea Doo RXT?

P0106 – ECM – Intake pressure out of range. Sensing port dirty or blocked. Sensor failure or unexpected reading at idle. Sensor fallen out of housing or intake leaking. Intake pressure sensor – 3 pin connector. Pin1 – 5 volts. Pin2 – 0 volts. Pin3 – 0 volts. Would it be an expensive fix ans can you DIY?

How old is a 2009 SEA DOO ski?

Recently I bought a 2009 RXT IS from a guy on craigslist. ski had 63 hours and 7 years old. ski had about 2 or 3 light abrasions on the hull, not scratches, and you could tell it was beached a few times in it’s lifetime (bottom of hull wasn’t glossy, more of a smooth matte color amd texture).

What do you need to change oil in a Sea Doo?

You’ll also need some tools like an E-10 Torx socket, a suction pump (known as a Sea-Doo oil extractor), funnel, and an oil reservoir or jug to store the drained oil. You can find complete Sea-Doo Oil Change Kits on the market, which includes the right amount of oil, filter, O-ring, and sometimes even the suction pump.

Navigation