Where is the brake light switch on a Sportster?

Where is the brake light switch on a Sportster?

This is the rear brake light switch. The front brake light switch is located in the right side handlebar switch housing. If neither switch works the brake light, odds are you have a short circuit in the wiring from the rear brake light switch to the rear brake light itself.

Why is my tail light not working on my Sportster?

You can’t post conmments that contain an email address. try starting with the bulb. brake light bulbs are dual fillament, meaning you have 2 bulbs in one basicly. if your brake side has blown then the tail light could still work.

Why is my rear brake light not working?

To begin with, there is no relay for the brake light. That thing you hear clicking is a circuit breaker. You probably have a short circuit between the rear brake light switch underneath the bike and the brake light itself. If the tail lights work, then you know what circuit is ok. Look at your rear brake master cylinder.

How does the brake light wiring system work?

How Brake Light Wiring Works. The brake light wiring system in most cars is not overly complex. At one end, you have the lights themselves: bulbs in sockets connected to a wiring harness. At the other end is the brake switch, where the pedal presses down and creates contact that completes the circuit. The system draws power from the car’s battery.

This is the rear brake light switch. The front brake light switch is located in the right side handlebar switch housing. If neither switch works the brake light, odds are you have a short circuit in the wiring from the rear brake light switch to the rear brake light itself.

What kind of brake light switch does a Harley Davidson use?

Our collection of Harley-Davidson brake light switch models keep you safe on the road while ensuring you have the right hardware hooked up to this critical bike part.

You can’t post conmments that contain an email address. try starting with the bulb. brake light bulbs are dual fillament, meaning you have 2 bulbs in one basicly. if your brake side has blown then the tail light could still work.

Why does my brake light stay on on my Harley Davidson?

The brake lever and master cylinder plunger have been known to wear and get stuck. Squeeze your front brake lever and press down on your rear brake lever; you only need to apply a small amount of force.

What kind of brake switch does a Harley Davidson use?

Front brake lines hose pipe ABS Harley Davidson Dyna wide glide switch back 4… 5.0 out of 5 stars. 4.0 out of 5 stars. 3.5 out of 5 stars.

What is part number for rear brake light?

The Front brake switch didn’t activate the rear brake light, I ordered a sensor from Harley ( part number 72001 – 69B ) and installed it. This is the part number for a rear brake light sensor to fit a 1984 FXWG wide glide shovel ) Check you have the right part number for your bike before ordering. Loading…

Where is the brake light switch on a Harley Davidson?

After assembly, the shim gets removed and the lever’s contact tab will rest against the switch all of the time, except when the front brake is applied. The front brake light switch has changed very little over the years and makes how to replace a brake light switch on a Harley fairly straightforward.

The Front brake switch didn’t activate the rear brake light, I ordered a sensor from Harley ( part number 72001 – 69B ) and installed it. This is the part number for a rear brake light sensor to fit a 1984 FXWG wide glide shovel ) Check you have the right part number for your bike before ordering. Loading…

What does it mean when your brake light is stuck?

A majority of the time, the brake light is actually stuck on. This, most typically, is an indication that your front brake light switch is misaligned or broken. There are a few common ways a front brake switch gets damaged.

Is there a sensor for front brake light?

Please try again later. The Front brake switch didn’t activate the rear brake light, I ordered a sensor from Harley ( part number 72001 – 69B ) and installed it. This is the part number for a rear brake light sensor to fit a 1984 FXWG wide glide shovel ) Check you have the right part number for your bike before ordering. Loading…

Posted In Q&A