What kind of ignition plug does a Honda CB750K use?
Fits: Honda CB750K (1969-72) with round wire harness to switch connector plug. Honda Ignition Switch Base unit repair Kit (including base cover). This is a replacement for the above ignition switch only CB-70309. Honda CB750 Contact Point Set (1pc.) – Right Hand Side Honda CB750 Contact Point Set (1pc.) – Left Hand Side Order quantity needed.
How big are the holes in a TCI ignition coil?
Replaces stock factory Tci ignition coils. 6.6mm mounting holes spaced at 102mm mounting holes center to center. Single Tower High Output Ignition Coil 3.3 OHM Primary Resistance, 15K OHM Secondary Resistance.
What should the coil reading be on a Honda CB 750?
If using stock coils, you should get a reading of approx 5 ohms. If using DOHC or most aftermarket “hot” coils the reading should be about 3 ohms. If your readings are very far off from the given values, the coil is probably bad. If you do not get a reading, or if it flickers in and out, then there is a broken wire and the coil is bad.
What kind of ignition switch does a Honda have?
Ignition Switch – Fits: Early CB750 – Round Plug (6 Hole, 4 wire) type. Fits: Honda CB750K (1969-72) with round wire harness to switch connector plug. Honda Ignition Switch Base unit repair Kit (including base cover). This is a replacement for the above ignition switch only CB-70309. Honda CB750 Contact Point Set (1pc.) – Right Hand Side
What is the contact point set on a Honda CB750?
Honda CB750 Contact Point Set (1pc.) – Left Hand Side This dual coil assembly is plug and play. Original factory specifications. It comes just as it’s shown in the photo. The coils are already attached to the hardware. Just bolt the assembly to your frame. The spark plug wire leads are labeled 1, 2, 3 and 4.
How big is the spark plug on a Honda?
Honda Spark Plug Fitment Chart Manufacturer Model Standard Plug Iridium Plug Electrode Gap HONDA @ 125 (NES 125) NGK CR8EH-9 0.8-0.9 MM HONDA ANF 125 INNOVA NGK CPR6EA-9 0.9 MM HONDA CA 125 REBEL NGK CR6HSA NGK CR6HIX 0.7 MM HONDA CB 1000 F NGK DPR9EA-9 NGK DPR9EIX-9 0.9 MM
How to replace handle lock on Honda CB750?
Install the Switch On the bracket and positively connect the coupler. b. Replacement of handle lock Removc the handle lock Case mounting screw With a cross point screw driver and remove the lock case 2. Insert the key into the handle lock and turn counter clockwise approximately 600 and then the handle lock can be removed from the steering stem.
What should primary resistance be on Honda CB 750?
PRIMARY RESISTANCE Set the multimeter to measure ohms. Use one test lead on each of the small terminals that attach to the wiring harness. If using stock coils, you should get a reading of approx 5 ohms. If using DOHC or most aftermarket “hot” coils the reading should be about 3 ohms.
What are the specifications of a 1981 Honda CB 750 C?
1981 Honda CB 750 C. Picture credits – Blue Custom. Submit more pictures. More pictures… 3.8 See the detailed rating of design and look, engine performance, reliability, fun-factor, etc. Compare with any other bike.
What kind of spark plugs do I Need?
Capable of sustained 75KV output with 14v DC input. Replaces stock contact point ignition coils on All 1970 & up models. Requires 7mm Dia. High tension spark plug wires (order separate). (Round Plug (6 Hole, 4 wire) type. This wire harness is made according to OEM specifications. As shown in photo.
What kind of ignition coils do 650’s use?
Ignition Coil – Exact Replacement Original Type Coil for all 650’s with Contact Point Ignitions. Hitachi type CM11-50/50B/52A The coils are not polarity sensitive, and are not marked + or – for that reason. The coil wires are 21″ long. Designed to replace most four cylinder OE coils.
Fits: Honda CB750K (1969-72) with round wire harness to switch connector plug. Honda Ignition Switch Base unit repair Kit (including base cover). This is a replacement for the above ignition switch only CB-70309. Honda CB750 Contact Point Set (1pc.) – Right Hand Side Honda CB750 Contact Point Set (1pc.) – Left Hand Side Order quantity needed.
Where can I buy replacement parts for my Honda CB650?
Our selection of Honda CB650 aftermarket mods and OEM parts allows you to find the right replacement for your bike’s damaged systems. Simply input information about your bike in our search tool. Then, click through to find the Honda CB650 replacement parts on sale that you need to restore your bikes potential.
Honda CB750 Contact Point Set (1pc.) – Left Hand Side This dual coil assembly is plug and play. Original factory specifications. It comes just as it’s shown in the photo. The coils are already attached to the hardware. Just bolt the assembly to your frame. The spark plug wire leads are labeled 1, 2, 3 and 4.