How much does a 1957 Panhead motorcycle cost?
1957 Panhead, Retitled as a 2000 Homade Harley Davidson 300 Miles on new motor New front end S&S Heads S&S Bottom end Kick & Electric start Just recently added turn signals to get inspected Asking $10,500.00 for bike as is, or $12,500.00 for bike & extra parts.
When was the last year Harley Davidson made a panhead?
WE JUST GOT THIS IN, DON’T MISS OUT, HERE IS A VERY RARE 1957 HARLEY DAVIDSON PANHEAD FL. IN 1957, THERE WAS ONLY (1,579) FL MODELS MADE. 1957 IS THE LAST YEAR HARLEY DAVIDSON USED THE HARDTAIL FRAME FOR PANHEAD MOTORCYCLES. THIS MOTORCYCLE HAS BEEN WITH THE SAME FAMILY SINCE 1957.
What are the parts for a knucklehead Panhead?
For Knucklehead EL FL 1936-1947 | Panhead EL FL FLH 1948-1965 | Shovelhead FL FLH 1966-1984. Dash and gauge Knucklehead panhead shovelhead 36-84. Bases, Covers, Fuel Gauge, Housing, Indicator Light, Knob, Mount, Speedometer, Tachometer. Knucklehead EL FL 1936-1947 | Panhead EL FL FLH 1948-1965 | Shovelhead FL FLH 1966-1984
What kind of engine does a 1957 Harley Davidson have?
THIS MOTORCYCLE HAS BEEN WITH THE SAME FAMILY SINCE 1957. THIS 1957 HAS TONS OF ORIGINAL (OEM) HARLEY DAVIDSON PARTS, HERE IS JUST A SMALL LIST OF SOME OF THE MAIN PARTS,#1) (H-D FRAME), THIS IS AN UNCUT / UNMOLESTED FRAME COMPLETE WITH THE SIDE CAR LOOPS AND ALL THE MOUNTING TABS, (H-D ENGINE), (H-D TRANSMISSION) (H-D FRONT END).
1957 Panhead, Retitled as a 2000 Homade Harley Davidson 300 Miles on new motor New front end S&S Heads S&S Bottom end Kick & Electric start Just recently added turn signals to get inspected Asking $10,500.00 for bike as is, or $12,500.00 for bike & extra parts.
WE JUST GOT THIS IN, DON’T MISS OUT, HERE IS A VERY RARE 1957 HARLEY DAVIDSON PANHEAD FL. IN 1957, THERE WAS ONLY (1,579) FL MODELS MADE. 1957 IS THE LAST YEAR HARLEY DAVIDSON USED THE HARDTAIL FRAME FOR PANHEAD MOTORCYCLES. THIS MOTORCYCLE HAS BEEN WITH THE SAME FAMILY SINCE 1957.
What kind of motor does a Harley Panhead have?
It is a 74″ Motor with .030 over New pistons, rings, honed cylinders, and a complete top end gasket kit. It has an S&S super E carb with .68 and .28 jets. It has an H-D 4 speed tranny, new coil, 40 spoke front wheel with mechanical brake and the rear has a solid wheel with juice brakes, tires are in good condition.
What kind of bike is a 1948 Panhead?
It is a clean Or title bike. THATS RIGHT,A GENUINE 1948 FRAME I HAVE HAD THIS FRAME FOR A WHILE WAITING FOR A PROJECT TO DEVELOP BUT TURNS OUT IT WASNT A 48,THIS FRAME IS VERY NEAR PERFECT.IT HAS BEEN REPAIRED ONCE BY THE FACTORY AND MAYBE NEVER USED SINCE.HAS THE SMALLER COIL BLOCKS AND ROUND TUBING IN THE FRONT.FRAMES IN THIS CONDITION ARE RARE.
What was the ignition timing on a 1961 Panhead?
Early 1961 fly wheels have only one mark for front cylinder and require use of a gauge to determine position of piston in rear cylinder. factory ignition timing instructions for 61-64 can be found here ” https://justpanhead.com/wp-content/uploads/2013/08/Factory-HD59-69-Pan-Shovel-Service-Manual.pd f ” page 197.
Where is the ignition mark on a Harley Davidson Panhead?
1948 -1960 used a single contact point manual advance ignition timer. mark should be in center of timing hole for advanced position. slightly before center for retard position. factory ignition timing instructions for 48-60 can be found here ” https://justpanhead.com/wp-content/uploads/2013/05/1948-57-EL_FL-service-manual.pdf’ ” page number 208
Early 1961 fly wheels have only one mark for front cylinder and require use of a gauge to determine position of piston in rear cylinder. factory ignition timing instructions for 61-64 can be found here ” https://justpanhead.com/wp-content/uploads/2013/08/Factory-HD59-69-Pan-Shovel-Service-Manual.pd f ” page 197.
How many horsepower does a panhead Panhead motorcycle have?
Engine displacement was 73.73 cubic-inches (advertised as 74ci), which was derived from a 3.44″ x 4″ bore and stroke. With 7:1 compression ratio, output was 50 horsepower at 4,800 rpm.