Why does my Suzuki C42 bike not start?
There is an internal 100 ohm resistor inside the ignition switch which is used as an anti-theft feature (to avoid simple bypass). When key-switch is turned on, one pole of the ignition switch connects the 12V battery power from the red/black wire on the ignition harness via the 100ohm resistor to an output on the Orange/Red wire.
Why does my Suzuki GSXR have a Fi warning?
Originally when the full exhaust Yosh RS-3 was installed all was done was the black/brown wire from the ECU input will prevent that “Fi” warning message from appearing in your instrument panel. That was the only wire cut, that’s it.
What to do if your bike won’t start?
3. Connect your test leads to measure resistance between the red and orange/yellow wires of the harness going to the key-switch – this should be ‘open’ with switch off and 100 ohms with switch on. If NOT 100 ohms, then you have bad ignition switch. 4.
What is the F1 code on a Suzuki GSXR 1000?
Click to expand… This is weird, after riding my 2002 GSXR-1000 over 19,000 miles I get the F1 code C46. I follow the directions according to the link which the white connection was still plugged up to the Servo and splice the other two wires B/R & R/B. Code is gone which I tested this after for over 1 hour.
Are there any known issues with the Suzuki SV1000?
Known issues…the bike is solid. Just ride it and enjoy! The SV1000 site is full of info if your really want to do the research http://www.sv-portal.com/. Some known issues are documented in these forums. When I first bought my bike, I read through these forums for information (I also checked the sv-portal.com site).
Why is my Suzuki C42 light not working?
No fuel injection whirl when I turn the key, but starter turns over. Put it in dealer mode and C42 kicks out (Ignition switch) Check about every electrical connection and nothing loose or disconnected. Fuses are fine. The ignition switch worked before the shock switch.
Where can I find information about the SV1000?
The SV1000 site is full of info if your really want to do the research http://www.sv-portal.com/. Some known issues are documented in these forums. When I first bought my bike, I read through these forums for information (I also checked the sv-portal.com site). Reading the threads will definitely help you.
3. Connect your test leads to measure resistance between the red and orange/yellow wires of the harness going to the key-switch – this should be ‘open’ with switch off and 100 ohms with switch on. If NOT 100 ohms, then you have bad ignition switch. 4.
What is the fault code for the GSXR ECU?
TP sensor, wiring/coupler connection. The sensor voltage should be the following. (0.15 V < or = sensor voltage < 4.85 V) Without the above range, c15 is indicated. ECT sensor, wiring/coupler connection. The sensor voltage should be the following. (0.15 V < or = sensor voltage < 4.85 V) Without the above range, c21 is indicated.
What is the fuel pump relay fault code?
Crankshaft position sensor (pickup coil) signal is produced, but fuel injector signal is interrupted continuous by 4 times or more. In this case the code C32, C33, C34 or C35 is indicated. When no signal from fuel pump relay, c41 is indicated. Fuel pump relay, connecting lead, power source to fuel pump relay.
What is the CKP code on a GSXR?
TO sensor, wiring/coupler connection. CKP sensor (pick-up coil) signal is produced but signal from ignition coil is not produced continuous two times. In this case, the code c24 or C25 or C26 or c27 is indicated.
What is the F1 code on a Suzuki GSXR?
It is is small white connector that does not plug into anything, and has a rubber cap on one end. Click to expand… This is weird, after riding my 2002 GSXR-1000 over 19,000 miles I get the F1 code C46.
Originally when the full exhaust Yosh RS-3 was installed all was done was the black/brown wire from the ECU input will prevent that “Fi” warning message from appearing in your instrument panel. That was the only wire cut, that’s it.
Where is the dealer mode switch on a Suzuki GSXR?
Location of dealer mode switch and how to get the codes. The dealer mode connector is under the tail cowling on the left side of the bike, near the regulator/rectifier. It will have only two wires going to it.
What is the c00 code on a 2005 GSXR1000?
On 2005 GSXR1000 when I install the jumper I get the C00 code. How do I get rid of the F1 and light if nothing is wrong?Looked through everything listed and I did not see anything about it.