Is there a belt Trip Switch on a Kawasaki 360?
This has been the case with many 360 owners, they found them after looking further. There is a procedure in the Vforce folder for the Vforce to reset the light. The Vforce does not have a belt trip switch. Note: Disconnecting the battery does not reset the light.
Where are the plugs on a Kawasaki Prairie 360?
Then, find the black and grey plugs up under the gas tank cover. These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were.
How do you reset the belt light on a prairie 360?
Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them. Cut the key on to verify the procedure worked.
When to reset belt light on Kawasaki ATV?
However, the belt light may stay on after flipping the switch back to “ON”, or it may have come on automatically at 100 hours to get you to return the machine to the dealer for inspection even though the belt switch is not tripped. The following procedures will reset the light if the belt switch is not tripped.
Then, find the black and grey plugs up under the gas tank cover. These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were.
Where are the belt lights on a prairie 360?
These are on the clutch side, just above the belt snsor. Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them.
How do you replace a belt on an ATV?
This video shows how to remove and replace the Belt on a Brute Force or Prairie, Covers all models. Belt replacement is quick and easy once you have the primary clutch removal too. This method is by far the most straight forward and will not damage the new belt on installation. by Everything ATV UTV Reviews.
Is the Kawasaki 360 belt light the same as the 2003 650?
The 360 belt light behavior is very similar to the 2003 650. If at first you can not find the right connectors, keep looking deeper because they really are there in a similar location to the P650. This has been the case with many 360 owners, they found them after looking further.
Where is the belt light reset button on a Kawasaki P650?
Belt light reset procedure for late 2003 and later P650, P360, and BF650SRA. 1. Turn the ignition switch OFF. 2. Disconnect both sets of 5 pin connectors located above the CVT cover. Note: These connectors are located just beneath the shift handle on the right side of the 650; one is black and one is grey.
This has been the case with many 360 owners, they found them after looking further. There is a procedure in the Vforce folder for the Vforce to reset the light. The Vforce does not have a belt trip switch. Note: Disconnecting the battery does not reset the light.
Cut the key on for about 5 seconds, or untill you see the flashing lights momentarily blink differently. Then cut the key back off. Plug the grey and black plugs up the way they were. Don’t foget to fasten them back up to the frame, if you pulled the strap off of them. Cut the key on to verify the procedure worked.
However, the belt light may stay on after flipping the switch back to “ON”, or it may have come on automatically at 100 hours to get you to return the machine to the dealer for inspection even though the belt switch is not tripped. The following procedures will reset the light if the belt switch is not tripped.