Why does my ignition coil stop working on my Harley Davidson?
The longevity you get from your coil may depend on usage, demand on the coil or environmental conditions. The coil’s capacity may diminish over time, or simply stop functioning at once. If it is determined that your motorcycle has no spark; do not just assume that the problem is your coil.
Why does my Harley Davidson hard start when hot?
Hard starting when HOT, but the engine spins up fine, means either lack of fuel or weak, no spark. If your Dyna is EFI, your fuel pump is losing prime/pressure due to fuel line leak…look here: http://www.hdtimeline.com/diagnosti…lated/979-engine_dies_and_runs_in_spurts.html
Why is my spark plug not working on my Harley Davidson?
The main reason that causes the ignition coil to not fire is that when anything hinders coil voltage from the channel to the electrode gap at the end of the spark plug. This can involve damaged, worn out, poor quality spark plug or a cracked distributor.
What should I do if my Harley won’t start?
Everything works perfectly – Lights, hear the fuel pump kick on, signal, brakes, switches appear fine and I changed the gas to highest just in case and nothing. I checked spark by pulling a plug and starting while on the cyl. and no spark. Put a new coil in it and nothing. Cranks great and all is appearing to be fine but no fire/start?
Hard starting when HOT, but the engine spins up fine, means either lack of fuel or weak, no spark. If your Dyna is EFI, your fuel pump is losing prime/pressure due to fuel line leak…look here: http://www.hdtimeline.com/diagnosti…lated/979-engine_dies_and_runs_in_spurts.html
How can you tell if a Harley Davidson ignition coil is bad?
Harleys’ that run on a single-coil engine will make cranking sound, but there will be no spark from the cylinders. If your bike stalls while working, this is another sign that indicates there’s something wrong with the ignition coil. When some irregular sparks are sent to plugs from the coil, the issue occurs.
Can a bad ignition coil cause a bike to stall?
When fuel is present more than air, it is rich and otherwise, it is lean. Vehicle stalling: Bad ignition coil will cause your bike to stall while the engine is working. The engine does not start: one of the most common signs of a bad ignition coil is when the engine fails to start. Rough idling: Weak ignition coils make the bike jerk.
Everything works perfectly – Lights, hear the fuel pump kick on, signal, brakes, switches appear fine and I changed the gas to highest just in case and nothing. I checked spark by pulling a plug and starting while on the cyl. and no spark. Put a new coil in it and nothing. Cranks great and all is appearing to be fine but no fire/start?
What happens if there is no external signal to the ignition coil?
With no external signal to the coil negative primary post, voltage would travel through the ignition coil windings without inducing any secondary spark. A switch, or signaling device, triggers an interruption in the circuit.
How can I tell if my ignition coil has no spark?
If you see no spark, the coil is a good thing to suspect next. You’ll need a digital multimeter to check the resistance levels of your coil. The side terminals of the coil are marked positive (+) and negative (–) and these are where you can measure the resistance of the primary windings.
Why does my car have no spark when I start it?
As a result, This occurs after the ignition coil or module gets too hot. Furthermore, it could correct itself after the engine module cools. In some cases, a bad ignition coil will result in the vehicle not starting it all. A Bad Rotor Or Distributor Cap (cracks or carbon tracks that are allowing the spark to short to ground).
What to do if your ignition coil is not working?
Older ignition systems used breaker points to interrupt the circuit, while more modern systems “sense” the need for spark by means of a hall-effect switch or crankshaft position sensor. The ignition module uses the information to time spark generation. Test these components if the energized coil fails to function.
Why is there no spark in my ignition?
An ignition module requires some type of external input in order to activate. If your vehicle stalls unexpectedly during operation and will not start again, it is likely because of loose or corroded electrical connections in the ignition module. In this case, check the switch, clean oxidized terminals, and replace broken wires if necessary.
How do you get spark from ignition coil?
High voltage is then generated in the coil windings. Voltage transformation produced by the interruption coincides to each spark generated. Older ignition systems used breaker points to interrupt the circuit, while more modern systems “sense” the need for spark by means of a hall-effect switch or crankshaft position sensor.