What makes a virago ignition system work so well?
Virago Ignition Systems coils have two different windings (of wire) around the same metal core. The PRIMARY WINDING is made up of a few turns of big wire and has low resistance. This allows 12 volt current to flow through it easily, pushed by pressure from the battery. This current returns to ground (negative battery terminal) through the TCI.
What kind of controls does a Yamaha Virago have?
JAPANESE YAMAHA VIRAGO. JARDINE FWD CONTROLS INSTRUCTIONS PG.2 RIGHT REAR MOUNT BOLT AND BRAKE ARM WITH EXTENSION ROD BRAKE PEDAL ARM MOUNT WITH COTTER KEY LEATHERLIKE BAG MOUNTING BRACKET LOWERED LEATHERLIKE BAGS, CLICK ON “ORIGINAL” FOR A LARGER VIEW
Why does the side stand switch stick on a virago?
If the sidestand is up (the ground connection is made) then the TCI is happy and you drive off. But occasionally the side stand switch sticks part way, or otherwise makes less than full and proper contact. The power input to the TCI may then be intermittent, or low in voltage due to excessive resistance in the switch.
What is the fuse box on a virago?
THIS VIEW SHOWS THE POWER SUPPLY WIRE, AS WELL AS THE TOW VEHICLE CHARGING WIRE. THE FUSE BOX IS A PLASTIC CUTOFF HOUSEHOLD TYPE SIMILAR TO WHAT IS USED FOR AN AIR CONDITIONER IN THIS VIEW YOU CAN SEE THE TWO INTERIOR SIDE 12 VOLT SIDE LIGHTS MAC vs STOCK EXHAUST.
How many Yamaha Virago parts are left in stock?
Only 15 left in stock – order soon. . Only 3 left in stock – order soon. . Only 8 left in stock – order soon. . Only 4 left in stock – order soon. . Only 5 left in stock – order soon.
If the sidestand is up (the ground connection is made) then the TCI is happy and you drive off. But occasionally the side stand switch sticks part way, or otherwise makes less than full and proper contact. The power input to the TCI may then be intermittent, or low in voltage due to excessive resistance in the switch.
How does the Virago ignition system work on a motorcycle?
Before discussing the Virago Ignition Systems it is important to understand how the power to run it gets there. The power starts at the battery and then travels through the main fuse, the ignition switch, the ignition fuse in the fuse box, the engine stop switch, and on to the TCI, and coils.
How does the primary winding work on a virago?
The PRIMARY WINDING is made up of a few turns of big wire and has low resistance. This allows 12 volt current to flow through it easily, pushed by pressure from the battery. This current returns to ground (negative battery terminal) through the TCI.
Why does my viragofolk not have a spark?
Many Viragofolk like the Autolite Platinum AP63 plugs. no spark can be a bad coil, pick-up, plug wire, side stand switch, relay, poor connections.. start off by checking the side stand switch. if you feel it is the problem you can unplug it and jump it at the harness side. note- this is after you replace the spark plugs..
Why does my Yamaha Virago XV not start?
ViragoTechForum.com :: Yamaha Virago XV Forums That Rock!!! After a very long hiatus, I charged up the battery and tried to start my bike. It cranked and and didn’t start. I tried for a while and only got one pop. I figured I had flooded it and pulled the plugs. After I cleaned them I decided to see how strong the spark was. I didn’t see one spark.
How big is the engine in a virago?
Virago Specifications Engine oil With Filter Change 3.3 qts (3,100 cc) Without Filter Change 3.2 qts (3,000 cc) Engine Rebuild 3.8 qts (3,600 cc) Front Forks
What causes a virago engine to run bad?
The power input to the TCI may then be intermittent, or low in voltage due to excessive resistance in the switch. In such cases your engine will run badly with various symptoms coming and going. It is hard to riders to figure out what is going wrong because you wouldn’t suspect the sidestand switch unless you knew about it.
Many Viragofolk like the Autolite Platinum AP63 plugs. no spark can be a bad coil, pick-up, plug wire, side stand switch, relay, poor connections.. start off by checking the side stand switch. if you feel it is the problem you can unplug it and jump it at the harness side. note- this is after you replace the spark plugs..