Why does my bike not start when I Turn on the ignition?
If okay, check that the switch is getting power from the ignition switch when the ignition switch is turned on. If not, your ignition switch may be faulty at the lead that supplies power to the starter switch and is probably the culprit because we know the ignition circuit works – it’s the starter circuit in question.
What should I do if my motorcycle battery wont start?
If you don’t see these symptoms or are otherwise unsure what to look for, the first step is ensuring that the battery is operational and providing the maximum voltage. To confirm your battery is still good, you should visually inspect it, check the voltage, and load test the battery. A visual battery inspection should involve:
Why is my push starter not working on my motorcycle?
Also, if the push starter was getting an electrical current and still not working, it would have drained your battery after about 10 tries with no engine turn over. So you most likely just need to replace the push starter.
What happens when you push the start button on a bike?
When you push the button it gives power to the starter to crank the motor. When you push start the bike, with it in gear you crank the motor manually, so check the connection (s) at or around the start button. As for the clutch hmmm does it engage, as in when you pull in the lever does it work as intended?
If you don’t see these symptoms or are otherwise unsure what to look for, the first step is ensuring that the battery is operational and providing the maximum voltage. To confirm your battery is still good, you should visually inspect it, check the voltage, and load test the battery. A visual battery inspection should involve:
Also, if the push starter was getting an electrical current and still not working, it would have drained your battery after about 10 tries with no engine turn over. So you most likely just need to replace the push starter.
Why does my Harley Davidson bike not start?
When I turn on the bike and put it in the run position, the fuel pump kicks on, but when I push the start switch the bike doesn’t even try to turn over. The battery is fully charged and the fuel pump turns on when I push the switch, but nothing else happens.
Why does my bike not turn on when I press the power button?
A low charge or a loose battery connection can cause your bike to not turn on when you press MODE or the power button. Follow the steps below to check that the battery is charged and correctly installed. Check the battery charge level. With the battery in place on the bike, use the key to turn on the battery.
What to do if your golf cart battery won’t start?
Leonard, If battery and solenoid known to be good, look in black box right behind the battery, take the cover off locate the 10 amp fuse and replace it if blown. If equipped with safety features like seat switch, safety neutral, etc. check/test that they are functioning properly.
If okay, check that the switch is getting power from the ignition switch when the ignition switch is turned on. If not, your ignition switch may be faulty at the lead that supplies power to the starter switch and is probably the culprit because we know the ignition circuit works – it’s the starter circuit in question.
Do you need deep cycle batteries for a golf cart?
It is a simple procedure to use a jumper wire to momentary touch the generator terminal to the battery terminal of the regulator. I will include a detailed site to look at. You just need a regular auto battery , you do not need a deep cycle as the unit doesn’t run off the battery. If it was an electric cart, you would want deep cycle batteries.
What to do when your Harley Davidson won’t start?
Try neutral with clutch pulled in. Also battery connections , solenoid wire. The security system lights only flash after I turn off the bike. I have the bike in neutral and I even tried pulling in the clutch a couple of times. I checked the wire to the solenoid and it had power.
What’s the voltage on a Harley Davidson starter?
I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.
Is the ignition coil on a Harley Davidson bad?
If you own a Harley Davidson bike, one of the things that might bother you is the ignition coil. Many riders face issues with the coil. However, for experts, identifying the problem is quite easy; but, it can be brain-racking for newbies or who isn’t familiar with motorbike mechanical issues.
What to do if your Dyna bike won’t start?
Apparently, starter issues are quite common on various Dyna models, so if yours is in need of replacement, see How to Replace Starter. If you are in a bind and your starter motor is acting up, a quick tap of the solenoid with a hammer or similar small object can sometimes free the starter to start the bike.