What is the charging system on a Harley Davidson?
The charging system on a Harley-Davidson motorcycle consists of the battery, the voltage regulator and the alternator.
What should the charging voltage be on a Harley stator?
You can use 13 as a good all around battery voltage. That is a good healthy battery staying charged just above 12 volts. Example only: Let’s say the stator is rated for 10 amps x 13-volt battery: 10 x 13=130 watt charging system. So you have a 130-watt charging system in this example.
Why is my Harley Davidson battery not charging?
If the stator fails, your battery will no longer be charging when you’re riding your motorcycle. Often times, a short can happen in the windings around the stator. The insulation on the wires can wear down over time or a wire can break.
What causes electrical problems on a Harley Davidson?
A Harley Davidson can experience electrical problems at any time, but there can be a wait for a service appointment at some repair shops. The most common cause of electrical problems on a Harley Davidson is the battery or the voltage regulator. Troubleshooting can be performed in any garage, and it saves on expensive service bills.
The charging system on a Harley-Davidson motorcycle consists of the battery, the voltage regulator and the alternator.
If the stator fails, your battery will no longer be charging when you’re riding your motorcycle. Often times, a short can happen in the windings around the stator. The insulation on the wires can wear down over time or a wire can break.
You can use 13 as a good all around battery voltage. That is a good healthy battery staying charged just above 12 volts. Example only: Let’s say the stator is rated for 10 amps x 13-volt battery: 10 x 13=130 watt charging system. So you have a 130-watt charging system in this example.
What happens if you have a bad voltage regulator on a Harley?
If there is anything wrong with the voltage regulator of your precious Harley, you will notice some unusual behaviors from the bike as follows – As I mentioned earlier, a bad regulator cannot control the voltage, which overcharges the battery. When the battery gets overcharged regularly, it causes the gas to escape from it.
What to do if your Harley loses voltage?
Testing the Voltage Regulator If you noticed your Harley losing voltage or suffering from voltage regulator symptoms, it’s possible to test the regulator for bleed. Voltage is only allowed to travel in one direction, from the stator to the battery, when the regulator is working properly.
How to test the charging system on a Harley Davidson?
Charging System Voltage Test Start motorcycle, measure DC Volts across the battery terminals (you should have a reading of approximately 13.2-15 DC Volts). 3. Check Connections/Wires Inspect the regulator/stator plug, and check the battery terminals for connection/corrosion.
Where does the charge lead go on a Harley Davidson?
The battery charge lead runs form the voltage regulator to the positive side of the battery. The AC output lead wire leads from the voltage regulator to the stator.
How do you close the Charger on a Harley Davidson?
This modal can be closed by pressing the Escape key or activating the close button. Tech review of the Harley Davidson charging system. Here’s an easy way to make sure your battery is charging.
How can I tell if my Harley Davidson battery is charging?
Tech review of the Harley Davidson charging system. Here’s an easy way to make sure your battery is charging. Everyone is at your house and ready to ride. You saddle up and CLICK, your Harley-Davidson does not start. Bob and Mark review an easy way to check your battery and make sure it’s staying charged. Click here to cancel reply.
How does cruise control work on a Harley Davidson?
The Harley cruise control function is governed by the motorcycle’s ECM. The ECM monitors the vehicle speed sensor (VSS) to… What do you do when it’s pouring outside and your brake light stays on?
This modal can be closed by pressing the Escape key or activating the close button. Tech review of the Harley Davidson charging system. Here’s an easy way to make sure your battery is charging.
Tech review of the Harley Davidson charging system. Here’s an easy way to make sure your battery is charging. Everyone is at your house and ready to ride. You saddle up and CLICK, your Harley-Davidson does not start. Bob and Mark review an easy way to check your battery and make sure it’s staying charged. Click here to cancel reply.
The Harley cruise control function is governed by the motorcycle’s ECM. The ECM monitors the vehicle speed sensor (VSS) to… What do you do when it’s pouring outside and your brake light stays on?
How can I tell if my motorcycle charging system is working?
So you have a 130-watt charging system in this example. Now, you can take the wattage of all those electrical accessories and see if you’re under or over your 130 watts and how much you have to play with. You can check your system by putting a volt meter on your battery. Or add a volt meter gauge to your motorcycle.
What to do if your Harley Davidson charger is not working?
Mike walks us through the process of a full charging system test, along with the removal of a complete Harley Davidson stator and rotor assembly on a Twin Cam touring model. If your Harley Davidson’s… Overview of Harley Davidson Stator Replacement Have you determined that your charging system was not functioning properly?
If there is anything wrong with the voltage regulator of your precious Harley, you will notice some unusual behaviors from the bike as follows – As I mentioned earlier, a bad regulator cannot control the voltage, which overcharges the battery. When the battery gets overcharged regularly, it causes the gas to escape from it.
What should the voltage be on a Harley Davidson battery?
Turn the ignition and start the bike. The volts should not drop below 9.6 volts when the starter engages. Turn the throttle to rev the engine. As the engine is revved, the volts should go up to 13 or 14 volts. Identify the wires. The battery charge lead runs form the voltage regulator to the positive side of the battery.
How does the battery work on a Harley Davidson?
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. Unless you have a kick-start, you’ll need a battery to get your Harley started and to keep it functional. With that can come some Harley Davidson charging problems.
How is the battery on a Harley Davidson charged?
Tech review of the Harley Davidson charging system. Here’s an easy way to make sure your battery is charging. Everyone is at your house and ready to ride. You saddle up and CLICK, your Harley-Davidson does not start. Bob and Mark review an easy way to check your battery and make sure it’s staying charged.
What kind of charger does a Harley Davidson use?
Your Harley-Davidson, or most motorcycles for that matter, use the same type of charging system, often referred to as a permanent magnet alternator. In a car, an alternator is belt driven. In a motorcycle, it is driven by magnets embedded around the flywheel.
Why is my Harley Davidson charging system not working?
It doesn’t sound like your charging system is functioning at 100 percent. Often, with age, grounds become an issue. Also, corrosion on pins & sockets. Especially on a model such as yours that has so many options.