How to replace a bad TSSM on a 02 FLHR?
1. Be sure the ignition has been OFF for 15 seconds or more before starting the procedure. 2. Set Run/Off switch to RUN. 3. Turn ignition key on, do not start. Verify that the Check Engine Light and Security Light come on, and wait for them to go out.
How to diagnose a Harley Davidson TSM / TSSM?
I {Heart} Hookers. To diagnose the TSM/TSSM observe the behavior of the turn signals. 2 Turn Ignition key On-Off-On-Off-On-Off-On and then toggle the Left Turn Signal switch twice. – – 3 Turn Ignition key Off-On Verify the Check Engine lamp and Security Lamp illuminate briefly and then turn off.
How to turn off ignition key on TSM?
7 Quickly (within 2 seconds) turn Ignition key OFF-ON Security Lamp remains lit for V-Rod and TC88 with TSSM. Lamp will not be on for TC88 TSM models. – 8 Wait until Security Lamp turns off or a minimum of 10 minutes has passed.
When does a TSM / TSSM starter relay go bad?
Starter relay could be bad (voltage present on pin 9) (Tn/Gn) when not starting engine. 35= TSM/TSSM bad. bank angle and tamper will not function when this code is set.
1. Be sure the ignition has been OFF for 15 seconds or more before starting the procedure. 2. Set Run/Off switch to RUN. 3. Turn ignition key on, do not start. Verify that the Check Engine Light and Security Light come on, and wait for them to go out.
I {Heart} Hookers. To diagnose the TSM/TSSM observe the behavior of the turn signals. 2 Turn Ignition key On-Off-On-Off-On-Off-On and then toggle the Left Turn Signal switch twice. – – 3 Turn Ignition key Off-On Verify the Check Engine lamp and Security Lamp illuminate briefly and then turn off.
7 Quickly (within 2 seconds) turn Ignition key OFF-ON Security Lamp remains lit for V-Rod and TC88 with TSSM. Lamp will not be on for TC88 TSM models. – 8 Wait until Security Lamp turns off or a minimum of 10 minutes has passed.
Starter relay could be bad (voltage present on pin 9) (Tn/Gn) when not starting engine. 35= TSM/TSSM bad. bank angle and tamper will not function when this code is set.
Can a TSSM be replaced by a TSM module?
Click to expand… Can you take a bike equiped with a TSSM, eliminate the alarm portion of it, and install a TSM module, replacing the TSSM module. Just what is the item being asked about ??
How did the key fob Batt get stuck in the TSSM?
There was a hairline crack in the TSSM ( don’t know how it got there) and water from washing got in and after much troubleshooting it was a goner = $200 later…Next while out on a ride the key fob batt checked out = stuck.
Can a TSM be installed on a ECU?
The marriage has to be disolved and then another unit can be placed, and either married to the ECU again, (TSSM) or a TSM can be installed. If you had an ECU from another identical bike, and a plain TSM, then you could elimiate the dealer trip. Not if you use your current ECU.
How to read a TSM / TSSM trouble code?
Current and Historic. If a trouble code is stored, it can be read using TSM/TSSM Diagnostics. Current trouble codes are those which are present during the current ignition cycle. problem is dropped and it becomes a historic code rather than a current code. Intermittent output shorts can become typical historic codes.
Can you re-install a TSSM on a new bike?
One of the advantages of doing this yourself is that you can keep your original module (along with a printout of this post) and re-install it at any time without another trip to the dealer, or if the bike’s new owner wants a security system.