How to adjust the clutch on a Honda motorcycle?

How to Adjust a Clutch on a Honda Motorcycle Step 1. Take the motorcycle for a 10- or 20-minute test ride. Use this ride to determine if the clutch is actuating… Step 2. Set the motorcycle on its kickstand or center stand so it will not tip or fall while being worked on. Step 3. Loosen the clutch …

When did Honda change the clutch on the CB750?

Around 1975 (This is a ’76 pictured) Honda introduced some revisions to help cure the clutch rattle these bikes are known for,and also to give a smoother engaging clutch. The revision for a smoother clutch was the addition of a larger outside clutch plate.

What causes the clutch on a motorcycle to drag?

A dragging clutch is one where the engine and rear wheel are not completely disengaged when the clutch lever is pulled in. The most common cause of this problem is a badly adjusted clutch. However, modern oils can sometimes cause this problem.

What happens if your clutch is not set up properly?

However, if your clutch is not set up and adjusted properly, it may do damage to both the engine and the transmission, and make for a long afternoon of walking or towing your bike. Keep your motorcycle running properly by keeping the clutch in good adjustment. Take the motorcycle for a 10- or 20-minute test ride.

How does the clutch work on a Honda motorcycle?

The clutch on a Honda motorcycle, when actuated, separates the driveline from the engine, effectively cutting power output to the rear wheel. This is an important feature, as it allows you to stop without turning off the engine, and also to switch gears while riding without damaging the gearbox of the motorcycle.

When to adjust the clutch on a motorcycle?

For example, if you release the clutch lever and the motorcycle is low on power, the clutch is not actuating enough. On the other hand, if you pull in the clutch lever and it is difficult to shift, or the motorcycle continues to propel itself forward, it is actuating too much, and should be adjusted.

How to adjust the clutch on a Honda 350?

Adjust following guide I’ve posted for 350/360 clutch adjustment (difference will be locknut means lock-bolt and screw means the slotted cylinder, otherwise, sequence and proceedure is the same)… A large coin held in vice-grips makes a non-damaging “screwdriver” for this process…

Where is the clutch adjuster on a Honda Accord?

Look at the top of the clutch pedal, near the pedal point, and you will see the adjuster for the Honda Accord’s clutch there. Turn the adjusting nut on the end of the clutch cable clockwise and test the pedal after each adjustment.

Where is the clutch fluid located on a Honda Accord?

Check beneath the hood first when you wish to adjust the clutch on a Honda Accord. Look on the left hand side where two reservoirs are located. Check the level of the second one as this is the one that contains the clutch fluid. If the level is below 3/8 of an inch or so from the top, add more fluid.

What should I do if my Honda Prelude clutch is not working?

Examine the master and slave cylinders in your Honda Prelude is you are trying to adjust the clutch and nothing is working. You may find that both or either are leaking. Replace these if this is so. Inspect the components of the clutch for wear, such as the teeth of the diaphragm spring, and the flywheel and clutch disc itself.

What should I do if my Clutch doesn’t work?

You should be able to move the clutch lever a short distance with no change in the clutch’s behavior. Tighten the clutch cable if you need the clutch to actuate less strongly. Tighten the cable at the crank case adjuster using a 13 or 15 millimeter wrench until there is only a small amount of play left in the cable.

How do you loosen the clutch cable on a car?

Loosen the clutch cable if the clutch needs to actuate more strongly and provide more power to the wheel. Loosen the clutch cable adjuster bolts near the crankcase using a 13 or 15 millimeter wrench until there is a small amount of play in the cable.

Navigation