Where is the accessory plug on a Harley Davidson?
The accy. plug I’m referring to is located down in the frame cavity in front of the battery box. It’ll have a rubber dummy cap plugged into it.
Where are the connectors on a Harley Davidson Street Glide?
Correct, 4 pin connector with two wires, B+ and ground. Yes I have different connectors on different bikes. Th 2017 street glide is a 6 pin connector under/inside the left side panel. I have never seen an 8 pin connector, not saying there aren’t any.
What is the switch on a Harley Davidson?
There are two , one thats got constant B+ and the other is switched thru the key . The switched B+ is a square connector with a rubber plug in it , the constant B+ is a grey plastic plug that has a terminated connect in it that gets removed .
Where is the Accy on a Harley Davidson Road King?
Depending on what year Road King you have , the accy. connector is located under the seat in front of the battery box . There are two , one thats got constant B+ and the other is switched thru the key .
Where is the aux cable on a Harley Davidson?
Pick a location on the back of the radio to drill a hole to run your AUX audio cable through. Use the appropriate size drill pit for the size of audio extension cable you purchased. I picked the location you see here, because I will never use the additional Harley modules.
How do you plug in a stereo on a Harley Davidson?
Using a sharp Exacto knife, cut into the board across the tracer. Before you put the radio back together, put the faceplate back on and plug the stereo back into the radio harness to test that you can select the AUX position without anything plugged in to the front AUX jack. If you can’t, then you have not cut the tracer.
Is there an auxiliary light on a Harley Davidson?
Well known aftermarket vendors like Kuryakyn and Harley-Davidson sell bolt-on auxiliary lighting for Softails. The extent to which extra lights brighten the road is open to debate. Many jurisdictions mandate that the extra light be turned off when the headlight is switched to high beam.
Where is the left toggle plug on a Harley Davidson?
The left “dead” toggle plug is located under the seat, it has a “stopper” in it and the plug itself is orange/black. First time on this site. Question about connecting accessories to this plug switched B+ plug.
How to wire an outlet and add an electrical outlet?
Rewire the Existing Electrical Outlet Connect the wires of the new cable to the existing wires. Strip about 10 inches of plastic sheathing from the new cable to expose the black, white and copper wires. Run the new cable, with sheathing, at least two inches up inside the box, and double over the excess wires to help hold the cable in place.
How to install a wire harness on a Harley Davidson?
Install the ring side of wire harness (3) to positive terminal. Position the fuse holder so it can be accessed. Do not install fuse now. Position the black 3-way connector near the vehicle connector [325]. Do not connect now. 2017 and later Touring models: Route harness (2) up the diagonal frame member toward the front of vehicle.
What to know when installing a Harley Davidson?
See an authorized Harley-Davidson dealer for advice about the amount of current consumed by additional electrical accessories or for necessary wiring changes. (00211c) When installing any electrical accessory, be certain not to exceed the maximum amperage rating of the fuse or circuit breaker protecting the affected circuit being modified.
The accy. plug I’m referring to is located down in the frame cavity in front of the battery box. It’ll have a rubber dummy cap plugged into it.
Rewire the Existing Electrical Outlet Connect the wires of the new cable to the existing wires. Strip about 10 inches of plastic sheathing from the new cable to expose the black, white and copper wires. Run the new cable, with sheathing, at least two inches up inside the box, and double over the excess wires to help hold the cable in place.
How do you install a GFCI outlet on an ungrounded circuit?
If installing a GFCI on an ungrounded circuit, refer to the manufacturer’s instructions. Place the red probe to each black wire until the tester lights up. This is the black wire that will connect to the Line brass screw terminal.
Where can I find a fitment for a Harley Davidson?
For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com (English only). This harness provides battery power, ignition/accessory power and ground connection from the eight-way Molex P&A accessory connector [325B] to accessories connecting through a four-way Deutsch connector.
Where is the accessory plug on a 2017 Street Glide?
Th 2017 street glide is a 6 pin connector under/inside the left side panel. I have never seen an 8 pin connector, not saying there aren’t any. Here’s a pic of mine. I have an accessory plugged into it. Normally there will be a black plug in the end of it. Red arrow pointing to it in first pic.
Where is the 16 pin connector on a car?
Since the implementation of the OBD standard, each vehicle has a standard 16-pin connector, as described on our OBD presentation page. The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate.
Where are the HDI connectors on a Harley Davidson?
The HDI connectors would be closer to the front of the bike , less wiring to deal with .
Where is the factory plug on a Ford Explorer?
For most applications, the factory plug is located beneath the dash, near the center console. If you have a Ford full-size van, the harness is underneath and to the left of the steering column. The Ford Explorer and Mercury Mountaineer have 6-pin connectors behind the glove box on the passenger’s side.
Th 2017 street glide is a 6 pin connector under/inside the left side panel. I have never seen an 8 pin connector, not saying there aren’t any. Here’s a pic of mine. I have an accessory plugged into it. Normally there will be a black plug in the end of it. Red arrow pointing to it in first pic.
Since the implementation of the OBD standard, each vehicle has a standard 16-pin connector, as described on our OBD presentation page. The norm states that the port must be located inside the vehicle passenger compartment. Depending on the make and model, it may or may not be easy to locate.