Is the Yamaha Grizzly 660 getting a clutch upgrade?
This totally “bone stock” 2004 Grizzly is getting larger tires and our 660 will be freshened up just a bit so we need to make sure the transmission can handle all the new power. In the photos you’ll notice the floorboard is already removed on the right side for a much easier attack on the clutch.
How do you change the clutch on a grizzly?
Pull the secondary clutch and belt off of the Grizzly. Once removed, the secondary clutch will be turned over to reveal the large spring and that’s what will be changed next. Using the 1-13/16ths socket, ever so gently loosen the spring-retaining nut approximately a HALF TURN.
Where are the rollers on a Yamaha Grizzly 660?
The rollers/weights are located in this part just under the thin metal cover, which is held in place by eight Phillips head screws. Carefully remove the screws and gently pry up on the cover being sure to not cut the rubber o-ring that seals the cover to its base. There will be grease inside this cover. Do not remove any grease from here.
This totally “bone stock” 2004 Grizzly is getting larger tires and our 660 will be freshened up just a bit so we need to make sure the transmission can handle all the new power. In the photos you’ll notice the floorboard is already removed on the right side for a much easier attack on the clutch.
How to rebuild a Yamaha Grizzly yfm700 clutch?
This guide will walk you through disassembling, inspecting and rebuilding a Yamaha Grizzly YFM700 clutch. The only specialist tool you’ll need for this job is a sheave holder. Watch the video above and use our Yamaha Grizzly clutch diagram for additional reference. Step 1.
Where are the clutch bolts on a grizzly?
Starting with the Grizzly’s clutch cover on the right side of the engine you’ll want to remove the clutch cover bolts with your 10mm socket. Begin removing the plastic clutch cover bolts but be sure to note the length and location, as these will vary and must be reinstalled in their correct location.
Why does my Yamaha Grizzly clutch keep slipping?
Sluggish acceleration or stuttering delivery of power is a sign that the clutch in your Yamaha Grizzly is slipping. If playback doesn’t begin shortly, try restarting your device.
How to troubleshoot Yamaha Grizzly 700 starting problems?
While your starter problem might be something incredibly simple, you might need a new battery or a starter relay. Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference.
Where is the Kill Switch on a Yamaha Grizzly 700?
Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference. Make sure the kill switch on the left handlebar side is in the “Run” position. It might seem like a “no brainer,” but it’s actually a common oversight.
Are there any problems with the Yamaha Grizzly?
It has steering control problems. Yamaha Grizzly power steering problems for their 2008, 2009, and 2010 models resulted in a recall of 20,000 units of 700- and 550-class Grizzlys and hundreds of rollover accident lawsuits.
Why does my Yamaha Grizzly 700 make a clanking noise?
It makes a clanking noise when in 2WD or 4WD. This problem usually happens after gassing on Yamaha quads hard. The initial speculation is that this is due to a snapped axle. Issues with bearings and axles may be the case for Yamaha ATVs that have been modded.
What to do if your Grizzly 700 is having problems?
Below are some things you can do to prevent these problems: Verify that the battery registers 12.5V or higher. This is a good first step, especially when troubleshooting 2008 Yamaha Grizzly 700 problems with startup. Anything below the said value is indicative of an unhealthy battery, which would mean a replacement.
Is the Yamaha Grizzly 700 a good quad?
The Yamaha Grizzly 700 is a reliable and tough quad. With its durable frame, it can endure harsh conditions and aggressive riding styles. But it’s not all perfect.