Are there any problems with the Yamaha Grizzly 700?
The engine is noisy and overheats. The Yamaha Grizzly 700 only has one cylinder, which many consider a drawback. With less power, it creates more noise than two-cylinder quads. It may also lead to overheating problems. If you experience this, adding a radiator should solve the problem.
Why is my gas tank not working on my Grizzly 700?
The gas tank rollover valve is defective. After removing the gas cap on your Yamaha Grizzly 700, you may notice a loud hiss. This is because your rollover valve is not venting properly and is defective. Supposedly, this was an issue seen in earlier models, which Yamaha corrected with an updated rollover valve.
Why is my Yamaha Grizzly hard to start?
Cold-weather starting is difficult. Owners of 2016 and more recent Yamaha Grizzly models complain that the engine is difficult to turn over and will not cold-start, despite the electrical starting system working correctly. This problem is caused by a broken decompression spring weakened during manufacturing.
Can you get 700 horsepower on a grizzly?
Grizzly 700 free horsepower? I saw this review on the Grizzly and this is a copy/paste from the article about all you have to do is punch a few buttons on the display and you gain 16% more hp? Here’s a first in the ATV industry. You can increase the Grizzly’s power by 16% in seconds with no money and no tools!
Is there a way to increase the performance of a grizzly?
What if I told you there was a way to increase the performance of your new 2007 Grizzly by 16% without making a phone call or spending a dime?
How can I increase horsepower on my Grizzly Raptor?
It turns out that by following a very precise procedure of pushing buttons on the LCD gauge pod, you can raise or lower the amount of fuel being dumped into the cylinder of the Yamaha Grizzly, and by doing so, increase horsepower. Our Grizzly came from the factory with a setting of “0”.
What’s the average speed of a grizzly Raptor?
On the opposite end of the drag strip was an accurately calculated radar gun. As a baseline test and in stock form with only the GYTR exhaust and a setting of “0”, we were only able to hit 51mph by the end of the eighth mile strip. As we raised the amount of fuel by adjusting the settings in the instrument panel, we progressively picked up speed.
Why does my Grizzly make a clanking noise?
Your Grizzly would also have extreme pressure in the gas tank and have power problems under load. This problem may arise from several factors like contaminated fuel, worn-out spark plug, fuel-starved engine, or a bad fuel pump. 8. It makes a clanking noise when in 2WD or 4WD.
What kind of chip does Yamaha Grizzly 700 use?
Yamaha Grizzly 700 EFI Dyno-Boost power chip is designed to maximize the performance potential of your stock engine. Blow those sluggish stock settings away with this Magnum Yamaha Grizzly 700 EFI ECU chip.
What to do if your Grizzly 700 is having problems?
Below are some things you can do to prevent these problems: Verify that the battery registers 12.5V or higher. This is a good first step, especially when troubleshooting 2008 Yamaha Grizzly 700 problems with startup. Anything below the said value is indicative of an unhealthy battery, which would mean a replacement.
Are there any problems with the Yamaha Grizzly?
It has steering control problems. Yamaha Grizzly power steering problems for their 2008, 2009, and 2010 models resulted in a recall of 20,000 units of 700- and 550-class Grizzlys and hundreds of rollover accident lawsuits.
Which is the best Dyno boost chip for a Grizzly 700?
So if you are searching for stuff like that, the Yamaha Grizzly 700 EFI Dyno-Boost remapper chip is the best option. Dyno-Boost remapper chip has been proven to be a great asset for boosting engine power output.
Why is the reverse light on my Grizz 700 not working?
It thinks your in reverse so it limits your speed/RPM’s. Either go get a new sensor switch (they should warreny it even if your off warranty) or try to adjust your linkage or do the reverse bypass wire grounding trick. If you ground out the reverse wire it will for sure fix this problem.
Why does my Yamaha Grizzly 700 make a clanking noise?
It makes a clanking noise when in 2WD or 4WD. This problem usually happens after gassing on Yamaha quads hard. The initial speculation is that this is due to a snapped axle. Issues with bearings and axles may be the case for Yamaha ATVs that have been modded.
Is the Yamaha Grizzly 700 a good quad?
The Yamaha Grizzly 700 is a reliable and tough quad. With its durable frame, it can endure harsh conditions and aggressive riding styles. But it’s not all perfect.
What kind of fuel does a Grizzly 700 use?
The Grizzly 700 is a true go anywhere, do anything utility quad. Fuel is fed via the 44mm fuel injection throttle body, making starting much easier. It also keeps it running at idle speed with no hiccups even under cold morning situations.
Which is the best Yamaha Grizzly to buy?
Using its successful Grizzly 660 as a starting point, Yamaha improved it by redesigning the frame, enhancing rider comfort and introducing electronic power steering. The end result is the top-performing Grizzly 700 FI Auto 4×4 EPS.
Where is the Kill Switch on a Yamaha Grizzly 700?
Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference. Make sure the kill switch on the left handlebar side is in the “Run” position. It might seem like a “no brainer,” but it’s actually a common oversight.
How to get a quote on a Yamaha Grizzly?
If you would like to get a quote on a new 2008 Yamaha Grizzly 700 FI Auto 4×4 EPS use our Build Your Own tool, or Compare this ATV to other Utility ATVs. To view more specifications, visit our Detailed Specifications.
How to check the Diagnostic Code on a Yamaha Grizzly?
Diagnostic code number on display followed by checking method. • Fully closed position 15 ~ 20 Check with throttle fully closed. • Fully opened position 95 ~ 100 Check with throttle fully open. Pressure difference (atmospheric pressure and intake air pressure). Displays the intake air pressure. Set the engine stop switch to “RUN”, then
The engine is noisy and overheats. The Yamaha Grizzly 700 only has one cylinder, which many consider a drawback. With less power, it creates more noise than two-cylinder quads. It may also lead to overheating problems. If you experience this, adding a radiator should solve the problem.
What’s the price of a 2008 Yamaha Grizzly?
2008 Yamaha Grizzly 700 FI Auto 4×4 EPS pictures, prices, information, and specifications. Below is the information on the 2008 Yamaha Grizzly 700 FI Auto 4×4 EPS. If you would like to get a quote on a new 2008 Yamaha Grizzly 700 FI Auto 4×4 EPS use our Build Your Own tool, or Compare this ATV to other Utility ATVs.