Why is my Kawasaki MULE 610 not starting?

Vibration and everyday use broke the fuse, the thin wire inside where it connects to the end in the fuse. Though looking at it and meter testing it told me it was good.

Are there any problems with the mule 610?

Those are a couple random thoughts on this situation, for what they’re worth. @007 Mule 610. It will start and run for about a minute the dies. It blow 20 amp fuse. I am having this issue right now.

Where is the air intake on a mule 610?

Also-when the 610’s first came out, we were advised that some people would haul them backwards on the trailer. Meaning back it up onto the trailer. If you look at the air intake, it’s at the top of the roll bar in the back side of it.

Why does my mule 610 blow 20 amp fuse?

Intake valve gets a little tight and causes more reversion in the intake tract, which doesn’t help matters any. Those are a couple random thoughts on this situation, for what they’re worth. @007 Mule 610. It will start and run for about a minute the dies. It blow 20 amp fuse.

Vibration and everyday use broke the fuse, the thin wire inside where it connects to the end in the fuse. Though looking at it and meter testing it told me it was good.

What was the problem with my 02 550 mule?

Had the same problem with my 02 550 mule. Just a click but couldn’t get the engine to turn over. Sometimes it would start cold and after riding a while, if you shut it off…..click, click, click. Sometimes it wouldn’t start cold but if you waited a while, it would start.

How to start and stop Mule runtime engine?

Jump to… Startup and Shutdown Script Start Mule Start Mule as a Windows Service Start Mule as a Linux/Unix Daemon Start Mule from a Script Deploy Mule Applications Stop Mule Remove the Mule Service or Daemon Enable Anypoint Monitoring See Also Learn how to start and stop Mule runtime engine to deploy Mule applications.

How can I change the behavior of mule?

The behavior changes depending on the Mule edition you are using: After adding a new property, reinstall or restart the Windows Service. Add the property and ensure that its index is greater than the greatest index in the wrapper-additional.conf file. Otherwise, your property can be overridden.

How to troubleshoot a mule that will not start?

Everything was running fine put it up one night, went out the next morning was a little harder to start (normally fires right up said it kind of sputtered) road it around a little and then parked it went back later and it will not start turn over but will not start. So hear is what I have went through.

What’s the problem with my Kawasaki MULE 610?

Here is an on-line part sheet that showed the 27002 as a relay. I have never seen a 610 so I can’t be much more help. Also check for blown fuses. I had a 610, the same thing happened to me. I even replaced the ECM, you won’t believe what the problem was. The ground cable was oxidized and loose.

Why is my Mighty Mule gate opener not closing?

Mighty Mule Gate Opener Won’t Close. If the auto-close timer is not automatically closing the gate for MM360, try the following: Check to see that the auto-close timer is turned ON. Check to ensure that the #1 dip switch is set correctly for a Push to Open application. Check the adjustment of the open position limit.

What kind of Mule is my grandpa’s?

Hey folks this has me stumped hopefully you can help me figure it out, This is my grandpas mule 550 KAF300-C6.

Is the ignition switch on my610 mule bad?

I think the ignition switch on my610 mule is bad, turn key just clicks, had starter tested, batt new, lites work. In Motorcycle questions?

What’s the weirdest thing about a kawaskai mule?

Sometimes it would start cold and after riding a while, if you shut it off…..click, click, click. Sometimes it wouldn’t start cold but if you waited a while, it would start. Weirdest of all…..sometimes if you held the key in start position, after about 4 seconds it would start.

What causes a kawaskai mule to not start?

Click to expand… A defective Bendix or Starter Clutch as it is sometimes called could cause these systems. When you turn the key, the solenoid could energize and the starter motor could try to turn but if the Bendix is frozen it will not start . . .click-click-click!

I think the ignition switch on my610 mule is bad, turn key just clicks, had starter tested, batt new, lites work. In Motorcycle questions?

What did I do to my kawaskai mule?

I replaced solenoid, battery, cleaned all wire terminals only worked when battery was fully charged until I added the relay.

Why does my Kawasaki Bayou 220 not start?

A wider variation of topics More Popular or Trending content More relevant content to this discussion Looks good to me! kawasaki bayou 220 won’t start with battery. Did my Bayou 220 just quit me or what?

What should I do if my Kawasaki MULE wont start?

Let it pump a minute, then try to start the Mule. Also, make sure you are not trying to start with a low battery, that could be a life long effort. These require the battery be fully charged for the pump and relays to function properly. Do not jump start it from a running vehicle, or you will damage relays and the igniter and may never start.

Where is the battery on a Kawasaki MULE?

It is mounted to the frame in front of the battery, looks like fun to access, might be easier to remove battery to get to it. A couple LEDs shouldn’t hurt it as I use a winch for raising a snowplow on mine

What kind of engine does a Kawasaki MULE have?

For those really tough jobs, Kawasaki offered the MULE 3010 Trans4x4 Diesel. Its powerful 953 cm3diesel engine churned out mountains of torque for serious hauling and towing capability. Coil-reinforced shocks for the De Dion axle and leaf-spring rear suspension ensured a high load capacity.

Why is my Kaw 610 mule not charging?

By the way it can be removed from under the mule without removing the battery but beware of mud / dirt in eyes and hair. Update, got my new regulator installed and no change still not charging.

How do you check for Spark on Project Mule?

The easiest way to check for spark at the plugs is to remove a plug, reattach it to the plug wire and then ground the outside metal part of the plug to the block or any negative grounded part on the motor. Then spin the motor and look for spark at the plug electrode. This is best done out of direct sun light as the spark will be faint.

Where did the Kawasaki Project Mule come from?

I purchased this mule as a basket case, I later learned it was previously used on a construction site in Mississippi and near salt water, needless to say I have had my work cut out for me removing parts etc.. I have installed a new used motor, new electronics with ECU, and countless other parts.

Navigation