How to disarm a Harley Davidson no key fob?

Within three seconds, simultaneously press both the left and the right turn signal switches. After the turn signals flash once, the system enters the transport mode. With the fob removed, the motorcycle can be moved without setting off the alarm. With the fob present, turn the ignition switch to IGNITION to disarm the system. 1.

Where is the FOB on a Harley Davidson?

If you use the fork lock then you are really screwed and there is no way around that other than to get the key and unlock them. You need to be within about 5 feet of your bike with the key fob to get the bike started. So, say your key fob is on the work bench or key hook in your garage near your Harley.

What happens if you don’t put your FOB in transport mode?

If you don’t put it in transport mode then the alarm activated by motion detection can discharge the battery, as the signals will keep activating over and over. Transport mode allows the vehicle to be picked up and moved in an armed state, however, any attempt to start the engine when the fob is not within range will trigger the alarm.

How do you start a HDD without a fob?

1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window. 2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times. 3. Press the right turn signal switch 1 time to move to the next digit.

What happens if you lose your FOB on a Harley Davidson?

How can I change the pin on my bike FOB?

If your bike has security, as well as the fob it can have a backup PIN. It will be a five-digit number that your local dealer can change or set for you using the Digital Tech system. Once you know your PIN you can change it at any time yourself; follow the instructions in your owner’s manual. The process is very easy to do.

How to enter fourth digit of code on Harley Davidson FOB?

9 Press right turn switch 1 time. 10 Enter fourth digit of code (1) by pressing left turn switch 1 time. 11 Press right turn switch 1 time. 12 Enter fifth digit of code (3) by pressing left turn switch 3 times. Security lamp stops blinking and the odo- System is disarmed.

How to start a bike without a fob?

Here is how to use the code you jus entered to start your bike without the Fob present!! 1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window. 2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times.

What should I do if my bike FOB goes dead?

This way if the main fob’s battery goes dead I simply turn the battery around in the other one and it’s good to go. Also, with the battery disconnected in the fob I can keep the fob in one of the bike’s bags without worrying that it’s deactivated the alarm should someone get any ideas of rolling away with it.

How does the key fob work on a Harley Davidson?

The Harley Davidson Touring comes with a key fob, and even though you don’t need a remote to lock and unlock the doors on a motorcycle, it works as a security system. When you lock your Harley using your key fob, the security system activates, which means you won’t be able to start the bike again without pressing the key fob.

What happens if you lose your security FOB on a Harley Davidson?

If you have a security-equipped Harley-Davidson, you know that without your key fob present, the bike will not start. What you should also know is your PIN number, just in case you lose your key fob mid-ride. If you bought your bike new from the dealer, this information should have been given to you, but that is not always the case.

What kind of battery does a key fob take?

The battery on the key fob is bound to die at one point or another. Check your owner’s manual for the specific battery type that fits your key fob. Most models take 2032 batteries or equivalent. Use the thin blade to pry the key fob open.

What does a red key light on a Harley Davidson mean?

If the security light (the key) stays on solid (not flashing) and the bike starts and runs, it means the bike has thrown a DTC. (diagnostic trouble code) It is essentially the equivalent of the “check engine” light on a car. The procedure for checking the code is posted in the electrical section.

How does the alarm work on a Harley Davidson?

When transporting the motorcycle, place the system in the Transport Mode. Otherwise, the alarm activated by motion detection can discharge the battery. In the transport mode, the security system is armed without enabling the motion detector for one ignition cycle.

Where is the key fob on a Harley Davidson?

You need to be within about 5 feet of your bike with the key fob to get the bike started. So, say your key fob is on the work bench or key hook in your garage near your Harley. You start your beloved Harley and ride off into the sunset. You stop at your favorite watering hole completely unaware you do not have your key fob.

How to disarm the Smart Security system on a Harley Davidson?

Also, with the battery disconnected in the fob I can keep the fob in one of the bike’s bags without worrying that it’s deactivated the alarm should someone get any ideas of rolling away with it. Every once in a while I use the PIN to disarm the system to help me remember what the PIN is.

Navigation