Why is my motorcycle clicking when I try to start it?
The solenoid is a little magnet and when you turn the key, it shoots out a small gear that the magnet polarizes. Essentially, this gear starts turning which in turn starts rotating the flywheel in the engine. When you turn the key and the battery is dead, you hear the magnet trying to magnetize the gear which is what makes the clicking sound.
Why does my motorcycle start when I turn the key?
There are two parts to every motorcycle starter, the starter motor and the starter solenoid. The solenoid is a little magnet and when you turn the key, it shoots out a small gear that the magnet polarizes. Essentially, this gear starts turning which in turn starts rotating the flywheel in the engine.
What should I do if my motorcycle won’t start?
If the reading stays steady, your battery is good to go—and your motorcycle likely has another problem (or a few problems). Fortunately, there are other troubleshooting means that can help determine why your bike won’t start.
Why does my motorcycle not start with the side stand down?
Newer bikes (and some older ones) may refuse to start with the side stand down. Along with all the other high-tech sensors that are on board, your motorcycle might have a built-in code that keeps the ignition from starting if your kickstand is engaged.
Why does my bike keep clicking the start button?
Took the battery to local auto parts store and checked out just fine with good charge. Put battery back in and hit start same click sound. After repeatedly clicking the start button I tracked the sound to the starter relay. Well with one hand moving the relay around and one pushing the start button bike would start up.
Why does my motorcycle make a clicking noise?
You go out to your motorcycle, put in the key, and try to start it only to hear those annoying and dreaded clicking noises instead of the rumbling of the engine. Those clicking noises can ruin someone’s day pretty quickly. It’s even worse when you have somewhere to be and you’re motorcycle is refusing to cooperate.
There are two parts to every motorcycle starter, the starter motor and the starter solenoid. The solenoid is a little magnet and when you turn the key, it shoots out a small gear that the magnet polarizes. Essentially, this gear starts turning which in turn starts rotating the flywheel in the engine.
What to do if your starter doesn’t click?
If the the starter still clicks, clean ALL the battery cables and try again. This includes the Positive at the battery and the starter. The negative (ground) at the battery and the ground point. Also check ground strap from engine to frame. If it still clicks, disconnect the battery.
How to fix it: There is only one fuse that can affect the starting of a motorcycle. Every motorcycle usually has a main fuse which is between 30 to 50 amps (occasionally some bikes will have 20 amps). It is usually located off of the positive battery wire.
Why does my car not start after clicking?
The source of providing power to the flywheel is the starter motor. The battery is the source of power for all of the aforementioned components – so when the car won’t start after clicking, this could be due to the flywheel, engine, starter motor, or battery. Let’s discuss the common causes of why the car won’t start due to clicking.
Why does my Harley Davidson bike not start?
When I turn on the bike and put it in the run position, the fuel pump kicks on, but when I push the start switch the bike doesn’t even try to turn over. The battery is fully charged and the fuel pump turns on when I push the switch, but nothing else happens.
How to start a bike without a fob?
Here is how to use the code you jus entered to start your bike without the Fob present!! 1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window. 2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times.
What do you hear when you turn the key on a starter?
On starters with the solenoid on top (GM, most others) the solenoid grounds through the starter brushes, so when the brushes make bad contact you get the “silent treatment” when you turn the key. The small wire going to the starter solenoid should get 12 volts or so when the key is turned to “start”.
What causes a motorcycle starter to go bad?
A motorcycle starter goes bad usually because of age. Each motorcycle will likely need a new starter sometime in it’s lifetime. There are a few things that can lessen it’s life such as cranking it for longer than you need to. That can cause electrical connections to overheat and melt.
What are the signs of a bad starter relay?
Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter. Alternator – The alternator is designed to power all of your car’s electrical systems when the vehicle is running. It also recharges the battery.
Why does my bike make a clicking noise when I start it?
This post is to explain what the noise is and why it happens. The starter motor on a bike uses a lot of power to turn the engine. The starter button cannot handle the current that the starter draws from the battery so a large electric switch called a solenoid is used.
Can a blown fuse cause a starter to not start?
Blown fuse – Sometimes the simplest explanation is the best one. A blown fuse in the starter circuit could be the cause of a no-start problem. Broken or corroded wiring – Damaged or dirty wires to the battery or to the starter solenoid (or wires that are loose) can prevent sufficient power from reaching the starter.