How do you change the ignition on a hi-4 motorcycle?
1. Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 2. Disconnect wires going from ignition module (item 3) to coil (14). 3. Remove ignition cover plate and hardware (items 1 and 2). Save these items for later re-use. Remove ignition module (3). 4. Note location of timer plate (10).
What kind of coils do you need for Hi 4 ignition?
Coils used with the HI-4 must have at least 2 ohms primary resistance. Coils with 4 ohms or higher may be used, but may not produce optimum output. We rec- ommend the following coils depending on application: Dual Fire. Use hookup shown in Figure 5. You can use the OE coil.
What kind of spark plugs do I need for a Hi 4?
8/96 29000-4000A HI-4 Ignition With Dual Plug Heads.Use two Crane 8-3002 coils. You will have to fabricate a bracket to mount the second coil. Crane HI-Intensity Reactive Core spark plug wires or equivalent spi- ral core wires are recommended for maximum performance.
Where is the cable exit hole on a hi-4?
Rotate the HI-4 about 90 degrees to give bet- ter access to the cable exit hole in the gear case cover. On some early models it may be necessary to enlarge this hole. Install the HI-4 first, then push the cable through the hole. Align the V notch on the HI-4 same as the O.E. plate you removed.
1. Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 2. Disconnect wires going from ignition module (item 3) to coil (14). 3. Remove ignition cover plate and hardware (items 1 and 2). Save these items for later re-use. Remove ignition module (3). 4. Note location of timer plate (10).
Coils used with the HI-4 must have at least 2 ohms primary resistance. Coils with 4 ohms or higher may be used, but may not produce optimum output. We rec- ommend the following coils depending on application: Dual Fire. Use hookup shown in Figure 5. You can use the OE coil.
How do you hook up an ignition coil?
Connect the negative coil lead wire to the negative (-) terminal of the coil. Insert the high tension lead wire into the center post of the coil making sure it fully seats. Connect the negative (-) battery cable to the negative (-) terminal of the battery. Turn the ignition to the “on” or “run” position but do not start the vehicle.
What makes a hi-4 single Fire race ignition?
HI-4 Single Fire Race Ignitions (P/N 8-2100 ignition module only and P/N 8-4100 ignition kit) are true single fire, even at cranking speed. Each cylinder is fired independently and only on the com- pression stroke. Single fire operation increases engine power at high RPM, improves starting, and reduces the likelihood of backfiring at low RPM.
How do you turn on ignition on Crane Hi 4?
spark plugs with an alligator clip so you will not shock yourself. Turn on ignition. Loosen the standoffs holding camshaft position sensor and rotate it clockwise until timing LED goes out. The point at which LED goes off is TDC. Timing is now set approximately at TDC, which is correct for cranking conditions.
Why is my Crane hi-4 not working properly?
Sounds almost like the spark advance curve is going flat and since it pops under WOT the spark timing may be getting scattered. Aren’t the Crane ignition systems photo cell triggered?
What kind of ignition system does a hi-4 have?
The HI-4 replaces the original equipment (OE) electronic ignition system on 1978 and later models as well as the points and mechan- ical advance on early models. HI-4 Single Fire Race Ignitions (P/N 8-2100 ignition module only and P/N 8-4100 ignition kit) are true single fire, even at cranking speed.
How to turn on the transponder on an immobilizer?
Insert the first transponder key into ignition lock cylinder for registration DO NOT TURN ON. The Security light may blink indicating it has accepted the key. After 3-5 seconds remove the first key from the ignition. Security light should remain on indicating you’re still in programming mode. 3.
How does the Immobilizer work on a Toyota?
Here’s an overview on how the immobilizer system works on older Toyota and Lexus vehicles. When you insert the key, a coil near the ignition ring picks up the RFID signal from your key and sends it to an amplifier. The amplifier then decrypts it and sends it to the ECU.
What to do if you lose your immobilizer key?
Insert the second transponder key into ignition lock cylinder for registration DO NOT TURN ON. The Security light may blink indicating it has accepted the key. After 3-5 seconds remove the second key from ignition. Security light should remain on indicating you’re still in programming mode. 4.