How to check engine light on Harley Davidson?
Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.
What did the battery light come on on my Harley Davidson?
Rode about 70 miles yesterday. Everything was fine as usual. Stopped for gas. She fired right up. As soon as we hit the road the battery and engine light came on. Pulled into the next gas station and shut her down. Waited a few minutes and she started right back up but lights still on. Headed home.
Where is the tail light on a Harley Davidson?
The blue wire (?) in the fender connector should be the tail light (running light). You should have 12Vdc there. Does your bike have the brake light harness that makes the rear turn signals brake lights also? Check under the seat for the wiring harness? neither the hand break lever or the foot lever are doing anything.
Where is the turn signal on a Harley Davidson?
I dident notice any breaks in the wire running under the rear fender. Under your seat there should be a 3 or 4 wire connector to the rear fender. It should have a 1 Black,1 Red/Yellow, 1 Blue wires. There may also be a Orange/White for HDI models. Use a Volt meter or a 12volt test light.
Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.
How do you check the Diagnostic Code on a Harley Davidson?
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9.
When does the Check Engine light come on?
I put about 150 miles on it and then pulled the fairing off to replace the stock mirrors with fairing mounted type …..and now the “check engine light” and charging light both light up about a minute after starting the bike. The bike had the stock battery from 2007 in it which I replaced with a new one.
How can I clear a check engine light?
Try reading your codes and write them don if trouble. Hold your trip odometer button and turn on. Let go of button and you will enter. Look at trip odometer. Push 1 time and the p will flash. Push and hold to go into p. A code will show up. Write it down. Then push and hold to clear it. More than 1 code maybe there. Clear the same way.
When do you get a check engine light on a Harley Davidson?
If you own and ride Harley Davidson motorcycles, you may get a check engine light from time to time. It is inevitable. A check engine light can appear for a variety of issues, and rarely is it serious.
How to get a diagnostic code for a Harley Davidson?
The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run.
How do you reset the Check Engine light?
To do that, press and hold the odometer reset button for longer than five seconds until the word “clear” is displayed. Once you see the word “clear,” release the reset button. Repeat these steps as you cycle through the codes. Or, if you don’t want to clear the code, click the button until the display reads “END,” meaning the end of the codes.
Why does my check engine light keep coming on?
A check engine light can appear for a variety of issues, and rarely is it serious. It is annoying and, at a bare minimum, every rider should be aware of the process to clear the check engine light and be able to retrieve the code to find out what it means.
Why does my Harley Davidson have no fuel pump?
If battery static volts measure 11.6v or less with the ignition on the ECM won’t energize the system. am not getting any voltage at the 15 amp fuse at key on, also have battery charger on while testing. engine cranks at good speed. are there more powers and grounds at the battery then just the main positive and negative battery cables?
How do you close the Diagnostic Code on a Harley Davidson?
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes.
How are static volts measured on a Harley Davidson?
To test the volts at the fuse you’ll need to have the tester leads hooked up prior to turning the ignition on because it’ll only show a measurement for 3 seconds. If battery static volts measure 11.6v or less with the ignition on the ECM won’t energize the system.
Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.
This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. The Twin Cam allows us to see the Harley error codes also known as the diagnostic trouble codes.
Are there any problems with the new Harley Davidson?
This is one Harley to avoid. Yes, it’s a new bike, but the Livewire has had numerous problems in its short on again off again life. The electric bike has experienced problems with its charging system, which in turn led Harley to stop production of the bike in October of 2019.
How do you reset the odometer on a Harley Davidson?
Push odometer reset button in & hold. Turn ignition switch to Ignition and release the odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine, and cruise) should illuminate.
What to do when check engine light comes on?
Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.
Can you reset the cel code on a Harley Davidson?
You may think you need an expensive code scanner or computer to check and reset CEL codes on your Harley, but the Motor Company designed a diagnostic mode into the computer. All you need are your ignition keys and a finger, and a pen to write down the stored codes before resetting.
What to do if your engine light is on in limp mode?
Release the odometer reset button. Turn OFF the ignition switch. Perform a road test then shut your bike down. Recheck the DTC’s again by repeating steps 1 to 7. If the code is current it will reappear. Historic DTCs are stored for 50 ignition cycles before cleared.
How to reset the Check Engine light on a Harley Davidson?
Run/Off switch. In this instance, just as any other time you work on your motorcycle, make sure your motorcycle is on a level surface and firmly on the kickstand. With the engine switch on the off position and the run/stop switch in the run position, push the odometer trip reset button and hold.
You may think you need an expensive code scanner or computer to check and reset CEL codes on your Harley, but the Motor Company designed a diagnostic mode into the computer. All you need are your ignition keys and a finger, and a pen to write down the stored codes before resetting.