Why does my new Harley Davidson not start?
Newer model Harley’s have a safety switch to prevent the bike from being started in gear without the clutch pulled in. Be sure your bike is either in neutral or, if in gear, the clutch is pulled in before starting. So if you have made it this far, your bike is cranking and your fuel pump is operational, but you still have no ignition.
Are there any problems with the new Harley Davidson?
This is one Harley to avoid. Yes, it’s a new bike, but the Livewire has had numerous problems in its short on again off again life. The electric bike has experienced problems with its charging system, which in turn led Harley to stop production of the bike in October of 2019.
What’s the voltage on a Harley Davidson starter?
I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.
What should I do if my Harley Davidson stall?
Also clean and check both ends of the cables to start with. Click to expand… yea it was runing good before and it start fine as usual just when riding that it stall. i am going to take the battery off and get it checked and clean the end as u said thank you , hopefully thats the issue Yea hopefully it something simple.
What causes a Harley Davidson not to start?
Some other ideas: 1 Problem with security module or key FOB 2 Problem with clutch safety switch, or its wiring (if bike has it) 3 Bad relay (like you said)
I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.
Where is the start relay on a Harley Davidson?
It is the GRAY one. On the inside cover there is a label that will identify the START Relay. 4) Look at the bottom of the removed gray relay closely. You will see pin notation as follows. 87,,87A,,30,,85,,86. 5) Leave the relay REMOVED from the bike.
What do you need to start a Harley Davidson?
The bike has to have a signal from the key fob before it will allow the bike to start. The TSSM is the – turn signal security module ( Japan & Korean markets only) I asked the dealer is they could test the ECM and they said yes if it on the bike.
Newer model Harley’s have a safety switch to prevent the bike from being started in gear without the clutch pulled in. Be sure your bike is either in neutral or, if in gear, the clutch is pulled in before starting. So if you have made it this far, your bike is cranking and your fuel pump is operational, but you still have no ignition.
When did my Wife’s Harley start to misfire?
My wife’s 2005 FLHTCUSE2 began to develop problems a few weeks ago. After a short ride, we stopped for her to get gas. On the way home, her Harley started to misfire and run poorly. I lost sight of her so I pulled over. After about 15 mins she showed up and said her bike would not stay running.
What was the problem with my Harley Davidson?
After about 15 mins she showed up and said her bike would not stay running. At each stop, it would stall but would always start after the fact. It died in the driveway. We tried to troubleshoot the problem but have been unsuccessful so far. Checked the fuel pump, getting gas, changed the plugs and checked the wires for leaks, no leaks.
When was the last time my Harley died?
Yesterday (Thursday) I road her to work, going out after work, and home (~40mi) just fine, nothing out of the ordinary. Figured I was in the clear and it was just some freaky coincidence the day before
Why does my Dyna FXDC bike not start?
Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.