What are the diagnostic codes for a 2003 Road King?

Discussion in ‘ Touring Models ‘ started by Dennis, May 6, 2007 . Trying to help a guy with a “check engine” lite on a 2003 Road King. My Touring Model Diagnostic Manual is for a 2005 RoadGlide…….and appears to be somewhat different in the way the test is run and the codes it spits out.

How to check ECM code on fuel Moto?

Fuel Moto does not offer technical support for diagnostic trouble codes. The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley gauge cluster as well as a list of codes. 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold.

How to get the ECM code on a Harley Davidson?

The following procedure will instruct in retrieving and clearing ECM Diagnostic Trouble Codes and TSM/TSSM codes through the Harley guage cluster as well as a list of codes. 1- Turn Ignition switchto OFF & Run/Stop switch is to Run. 2- Push odometer resetbutton in & hold. 3- Turnignition switchto Ignition and release the odometer reset button.

What does Cal 03 mean on a Harley Davidson?

The CAL 03 will be the last one Calibration 3=Domestic. I Have a 2000 road king classic E.F.I. When scrolling threw my speedo to check codes. they all come up clear but at the end of the list after checking the last one Cal 03 come up. not sure what that means. Here’s some info about that for you. d10 is Speed output shorted low or open.

What does the Code 02 mean on a Harley Davidson?

If it were a current code, the light would remain lit while running. Above codes can also be set if 02 sensor fails. CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed.

When did my Wife’s Harley start to misfire?

My wife’s 2005 FLHTCUSE2 began to develop problems a few weeks ago. After a short ride, we stopped for her to get gas. On the way home, her Harley started to misfire and run poorly. I lost sight of her so I pulled over. After about 15 mins she showed up and said her bike would not stay running.

What kind of EFI system does a Harley Davidson use?

EFI systems that sense engine load by the use of the throttle or TPS (throttle position sensor) are referred to as an Alpha-N system. EFI systems that sense engine load by the use of a MAP sensor are referred to as a Speed-Density system. Harley-Davidson has used both types of EFI systems on its vehicles.

When does a Harley Davidson engine misfire at low speeds?

However, when cruising along about 25-30 mph (in either 2nd or 3rd gear) it is always misfiring and sputtering pretty bad now (had a little hint originally and definitely getting worse now). After coming to a stop, the idle is a bit rough and sometimes the engine acts like it wants to cut out for a few seconds after which it seems to idle OK.

What kind of bike is the 2003 Harley Davidson Road King?

2003 HARLEY-DAVIDSON FLHRCI ROAD KING ANNIVERSARY, Super clean and heavily upgraded 100th Anniversary Road King with fuel injection finished in the re… 2003 Harley-Davidson® FLHR – Road King®, 2003 Harley-Davidson® Road King®

Is the 2003 Road King Anniversary Edition flhrci?

2003 ROAD KING 100th ANNIVERSARY EDITION Job changes and a move mean this baby needs to find a new home. I simply don’t have time to ride it anymore…. 2003 Road King Anniversary Edition FLHRCI. Yes fuel injected Low miles 41,000. Lots off chrome and too much to list, but the pictures show it all. S…

When did I Sell my Harley Davidson Road King?

2003 HARLEY DAVIDSON FLHPI ROAD KING POLICE, We sold this one 2 years ago to a long time customer of ours. He stopped in to say hi and decided he want…

What is the DTC code for a speedometer?

Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). 1- Turn Ignition switch to OFF & Run/Stop switch is to Run. 2- Push odometer reset button in & hold. 3- Turn ignition switch to Ignition and release odometer reset button.

How do you check the Diagnostic Code on a Harley Davidson?

NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until ‘clear’ comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9.

What does a trip code on a Harley Davidson mean?

A “trip” consists of a start and run cycle, the run cycle lasting at least 30 seconds. After the 50 trip retention period, the trouble code is automatically erased from memory (that is, assuming no subsequent faults of the same type are detected in that period).

What does the word diag mean on the odometer?

The word “diag” should then appear. 4 – Push the odometer resetbutton once and you will seethe selection menu “PSSPt” with the first P flashing. 5 – Each letter represents an area of the diagnostics module.

How to get a diagnostic code for a Harley Davidson?

When do you record the same trouble code twice?

When you have recorded the same trouble code twice, it is an indication that the transmission has been restarted and that all trouble codes have been retrieved. IMPORTANT NOTE ..If diagnostic test wire is installed across Pins 1 and 2 on connector in lieu of a Scanalyzer, the ECM is placed in a diagnostic test mode and the engine will start.

Why does my odometer stop working on my Harley Davidson?

It’s located on the transmission just behind the rear pipe. A good quality gear lube will just about eliminate this problem. The magnetic speed sensor pick up gets fouled from the metal shavings in the transmission which causes the speedo to stop working and the directionals to stop self canceling because of no input to the ECM from the sensor.

What can cause an ignition switch to fail?

(These generalizations, depend significantly on year, make, and model.) Worn ignition switch contacts, temperature problems, or broken springs can all cause the ignition switch to fail, preventing you from starting your car. On the road, poor ignition switch contacts could shut the engine off while driving, which could be dangerous.

How often should you insert and remove the ignition key?

You may insert and remove the ignition key thousands of times every year, wearing the key and tumblers ever-so-slightly every time. Heavy keychains can add more stress to the ignition cylinder, increasing wear. After a while, the key may fall out of the cylinder or be unable to turn out of the lock position.

Can a unworn key turn an ignition cylinder?

Or, an unworn key may not turn a worn ignition cylinder, as they haven’t “worn together.” How To Fix It: The best way to do this is to get a new lockset, with new keys and a new cylinder. You might consider getting a matched lockset that includes the door and trunk cylinders.

Why did my Harley Road King start cutting out?

Would be great for a while and suddenly start cutting out. Found a bad wire on the start relay under the seat. Harley Mechanic said that was probably not the issue but replaced the relay, changed the wire connection and hasn’t missed a beat in two years. The wire that you found that was bad on that 2002 road king under your seat…

What kind of motor does a Harley Road King have?

I have a 2002 CVO road king with a stage three stroker kit installed. When the dealership install the package the bike ran fine for period of time. Now the bike will miss occasionally and cut off at low idol just after a miss occasionally.

Where is the bad wire on a 2002 CVO Road King?

The wire that you found that was bad on that 2002 road king under your seat… Was that right beside the battery or do they have something to do with a relay near the battery? I have a 2002 CVO road king with a stage three stroker kit installed. When the dealership install the package the bike ran fine for period of time.

How to check the fault code on a Harley Davidson?

Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC’s again by repeating steps 1 to 9. If the code is current it will reappear. 9 – Press and release the odometer reset button to continue to the next module.

How to know if your Harley has a V inerr code?

You may have a failing sensor on your throttle body. Look for one or more stored codes in your speedo head. A stored code should lead you in the right direction. If you do not have any stored codes; check for an intake leak. Hi, do you know what mean “V INERR” code? Hi, Andre. We would be happy to assist you; we just need some more information.

What to do if you get an error code on your Harley Davidson?

Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTCs again by repeating steps 1 to 9. If the code is current it will reappear. Press and release the odometer reset button to continue to the next module. Turn Ignition switch to OFF.

Why does my motorcycle engine keep backfiring?

When you are getting too much air and not enough fuel in your cylinder this is called running lean. A lean condition in your engine is terrible for the engine internals. Too little fuel in the cylinder and an excess amount of air can be the culprit to your backfiring problem.

What causes a Harley Davidson engine to ” fire “?

The engine is still spinning but the incoming fuel rate is very low, until just enough builds up in the combustion chamber to “fire” on the exhaust stroke of the engine. Don’t “change the plugs” like some people suggest, it’s a waste of time and money.

Is it dangerous to have a motorcycle exhaust backfire?

A motorcycle exhaust backfire is an annoying and potentially dangerous problem to have. It can damage your ears if you’re in a confined space, or could start a fire as some backfires even emit flames, I’ve almost had my hand burned once from a pesky backfire problems I was troubleshooting.

What should the idle speed be on a bike with EFI?

In fact, by design, the ECM lowers the RPM at higher temperature at idle to help reduce the engine heat. Also, for a bike with EFI, there is a low oil pressure warning light that warns you on low oil pressure. Typically, at idle oil pressure is 7psi to 12psi.

What kind of EFI does a 2000 fltrsei have?

I have a 2000 FLTRSEI that had MM EFI. I got tired of cold start/idle issues that I could not fix. My bike is a different case. Being a factory screaming eagle the program that was flashed to the computer was unique to the FLTRSEI. If I reflashed and ever wanted to go back to stock I would have had to buy anothe ECM fromHD with the FLTRSEI flash.

Is there a trouble free bike with mm EFI?

Magneti Marelli EFI 1999-2001-Does Anyone Here Have A Trouble Free Bike with MM EFI? I’m the original owner of a 2000 FLHTCUI and it was trouble free until this year, now I’m having issues with the MM EFI system and It’s starting to cost me money and aggravation chasing the EFI problems.

How to reset check engine light on Harley Davidson touring?

You may think you need an expensive code scanner or computer to check and reset CEL codes on your Harley, but the Motor Company designed a diagnostic mode into the computer. All you need are your ignition keys and a finger, and a pen to write down the stored codes before resetting. This article applies to the Harley Davidson Touring (2005-2016).

How do you reset the Check Engine light?

To do that, press and hold the odometer reset button for longer than five seconds until the word “clear” is displayed. Once you see the word “clear,” release the reset button. Repeat these steps as you cycle through the codes. Or, if you don’t want to clear the code, click the button until the display reads “END,” meaning the end of the codes.

How to troubleshoot an ICM error code on a Harley?

Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM and ICM/ECM Diagnostic Trouble Codes (DTC). Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release the odometer reset button.

What are the diagnostic codes for a speedometer?

Why do I have to test 3 wire cop coils?

The Power and Ground Circuits of the Coil-On-Plug ignition coil (type with three wires in the connector) have to be tested to find out the real reason you got a No spark result on your spark tester. Usually these circuits are fine and are providing their respective signals.

Can you fix a 1999 Harley Davidson Road King?

IF you find a low mile 1999 and 2000 bike for the right price. THE sure fix is there..

When was the first Harley Davidson Road King built?

ALL BIKES- twin-cam engines (regardless of model) built 1999 model year including the first 1/2 of 2000 model year, build date (dec. 15,1999) had the “potential” problem with the cam bearing coming apart.. “POTENTIAL” meaning many bikes held together not showing signs of a problem.

How do you know if your Harley Davidson has a trouble code?

The test wire must be removed from the data connector and the ignition switch turned OFF or the check engine lamp will continue to flash codes. A historic trouble code resides in the memory of the ECM until the code is cleared by use of the Scanalyzer or a total of 50 trips has elapsed.

What kind of idle problem does a road King have?

Rough idle, Carbon fouling the plugs, backfiring, and it sounds like the fuel pump is dumping way too much fuel. It is an 01 Road King with PCM3-USB, Arlen Ness Big Sucker Intake and Wild Pig Slip On’s. Please help!

When did my Harley Davidson Roadking idle down?

Discussion in ‘ Touring Models ‘ started by michael49, May 31, 2009 . The promblem started in November of last year. The bike would idle down and die when I stopped for a stop light. Took it to a non-Harley repair shop.

Is the idle speed motor on my 99 ultra bad?

I have a 99 Ultra with MM Injection. When I bought the bike 4 years ago the cold start/idle was terrible. Being in the car business it was not too difficult to diagnose as a bad idle speed motor. It actuated but once it touched the lever it would not move it.

What kind of Idle did my bike have?

My bike had an uneven idle, would stumble & cough at low RPMs (like turning a tight corner at slow speed) and generally ran OK, MOST of the time.

What does code 56 mean on a Harley Davidson?

Hi, Denver. Code 56 is-Crank Position Sensor/Cam Position Sensor Signal Error 41 is a ranking # and indicates check engine light open/low. These do not have anything to do with poor idle. 1st make sure that your intake is correctly sealed. Very common problem with your Magnetti Marelli assembly is the IAC sensor.

How to check engine light on Harley Davidson?

Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate.

What is the diagnostic code for a Harley Davidson Road King?

Cant find 88 on the list, Psspt method gives the d01CLr – d10CLr followed by a PPU then the number 84172. I looked for this 84172 number as a part number and found no such part. I aint rich who here is?

Navigation