What should I do if my Grizzly 600 has no spark?
I got the ATV home and I checked for spark (GOOD SPARK) replaced the spark plug (OLD PLUG GOOD TAN COLOR), check the fuel line, remove the needle and jet checked the float and reassembled. At this time the ATV started right up and idled and rev under throttle for about 5 minutes.
What happens if the stator on a grizzly goes bad?
If the voltage checks out, the next step is to test the stator, which is the component that generates the electricity your YFM700 relies on. A faulty stator means no power for your ATV. Watch the video above and follow the guide below to test the stator for your Yamaha Grizzly.
What should the stator reading be on a Yamaha Grizzly?
Measure between terminals 1 and 2; between terminals 2 and 3; and between 1 and 3. The reading should be around 20-25 volts. If the reading is very low, that particular winding is an open circuit and the stator has failed.
What do you need to know about Yamaha Grizzly yfm700?
The charging system on a Yamaha Grizzly YFM700 is made up of three components: the battery, the regulator/rectifier and the stator. If playback doesn’t begin shortly, try restarting your device.
Why are the wires on my Grizzly no spark melted?
Pulled out the stator the wires were melted together right before the grommet where the wires exit the case. Called Ricky Stator. They said it could be that the rectifier went bad and then there was nowhere for the current to go and it melted wires together. Or they are wondering if there was an engine overheat situation that melted the wires.
Is there a service manual for a Yamaha Grizzly?
We have a Yamaha service manualand checked everything, resistance on factory specs and also the ones for stator and pickup provided by Ricky Stator. Everything checks out fine. We cleaned the grounds and untaped the wiring harness and checked the ground crimps on the harness.
How to fix a Grizzly 600 with no spark?
Pull the plug boot off of the coil wire, make sure there is good clean wire at the end, if not, then clip a little bit of insulation off, about 1/8th inch at a time until you find good fresh wire.
Where can I post pictures of my Grizzly 600?
Join our Forum! As a member, you can post in our forums, upload your photos and videos, use and contribute to our downloads, create your own member page, add your ATV events, and even start your own ATV club to host your own club forum and gallery.
Where does the power go after starting a grizzly?
After starting, the ignition can get the power from the charging circuit, in your case from the rectifier. If the rectifier is bad = grounded you would have a robber to the power going to the ignition. The circuit sort of “Y s” itself after the rectifier.
What should the stator measure on a Yamaha 600 Grizzly?
The stator should measure little to no resistance within the coils, but from coil to ground on the engine should be nothing or it would be a grounded stator = no good. If you had a grounded stator it could have grounded the ignition system, but it would have also killed the battery.
Is there a spark when the starter is released?
No spark while cranking over with electric starter…however when releasing start button sparks one time only. Coil and stator already replaced. Open to any suggestions….I am thinking it has a bad ground somewhere but can’t find anything.
When do you crank, sparks when START button released?
Pickup coil. Cranks and cranks then sparks 1 light spart when starter button is released. Did you replace the pickup coil? If not, do so. If yes, did the old one and the new one look exactly the same?
What’s the problem with no spark when cranking?
Try the kill switch, sounds like the problem to me…i was having problems with spark and figured i had fixed them (witch i did) and when i went to test all i was getting was a spark when i let off….yah i didnt have it turned on) my BigBear was doing that exact same thing.
When did the Yamaha Grizzly 600 come out?
Read on. The Yamaha Grizzly 600 4×4, produced from 1998 to 2001, has a 595-cc four-stroke SOHC engine from the big-selling Enduro-style ’86 XT600 Ténéré – a culmination of Yamaha’s efforts to enhance the off-road performance of XT models further and make it more suitable for full-fledged rally competition.
I got the ATV home and I checked for spark (GOOD SPARK) replaced the spark plug (OLD PLUG GOOD TAN COLOR), check the fuel line, remove the needle and jet checked the float and reassembled. At this time the ATV started right up and idled and rev under throttle for about 5 minutes.
What kind of ignition does a Grizzly 600 have?
Ignition: The Grizzly 600 uses a CDI ignition with an electric and recoil start system. It has a CDI-magneto generator system that powers up electronic accessories.
What kind of oil does a Yamaha 600 Grizzly take?
Lubrication: Yamaha 600 Grizzly’s oil capacity at disassembly is 2.75 US quarts/2.6 liters, 2 US quarts/1.9 liters without filter replacement, and 2.1 US quarts/2 liters at oil filter change. Use 10W-30, SAE 5W, or 20W-40 Yamalube 4 4-stroke oil or its equivalent for best engine performance.
Why does my ATV not have a spark?
If you have a hard time being able to tell if you can see a spark or not, you could always have a buddy hold the electrodes of the spark plug. If he yells when you try to start the engine, you have spark. There are a few reasons an ATV won’t be getting spark from the spark plugs.
How to troubleshoot Yamaha Grizzly 700 starting problems?
While your starter problem might be something incredibly simple, you might need a new battery or a starter relay. Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference.
How can you tell if a spark is coming from a stator?
To make sure, check the wiring harness coming from your stator, If you see group of three wires of the same color (usually white, yellow, or black) you have a three phase stator. A single phase stator will not have that set of three wires.
Why does my Grizzly 600 have no spark?
do you have power to the coil from the cdi box. if you do not get some kind of crank signal from the cdi box then your coil will not spark. remove the plug wire and try to starting it. see if the coil arcs to itself. most will. if it does then put a new plug and wire on it. What year is your Grizzly?
While your starter problem might be something incredibly simple, you might need a new battery or a starter relay. Check out our Yamaha Grizzly 700 electrical parts diagram and starting motor parts diagram for reference.
How can I tell if my ATV engine is sparking?
To quickly tell if your ATV is getting spark, remove the spark plug from the engine. Reinsert the plug back into the coil wire. Hold the electrodes of the spark plug close to the engine to ground it, and try starting the engine. If you see spark coming from the end of the spark plug, your ATV engine is getting spark.
The stator should measure little to no resistance within the coils, but from coil to ground on the engine should be nothing or it would be a grounded stator = no good. If you had a grounded stator it could have grounded the ignition system, but it would have also killed the battery.
Why is my spark plug not working on my ATV?
This is the wire that hooks up to the spark plug when it is bolted into the engine. Sometimes these wear out because the wire itself is usually exposed to dirt, rocks, and debris while riding. If the spark plug wire looks good, the next step is to check for bad connections or bad switches.
Why does my Yamaha 600 Grizzly have no spark?
Had no spark. We tested and found it was the stator, changed the stator with one purchased from Ricky Stator. It ran fine about 4 hours while snow plowing and it died again. Again, no spark. We changed out the CDI box, ignition coil, new plug.
What’s the problem with my Grizzly 600 ATV?
The problem appeared while running down a level dirt road at 50 Km/hr and then the ATV just quit running. I coasted to the roadside, stopped and restarted the ATV right away. I then drove another 20 K when it once again quit running while going down a hill, I stopped once again to restart the ATV but she won’t stay running.
What to do if your Grizzly has no spark?
Just wondering. Location: Iowa!!!!! Try going to your kill switch, pull the wires and check continuity across the contacts. Then go to your tranny switch for the neutral safety, pull the wires and hot wire across the two ends = make sure it’s in neutral. See if that gets you a spark.
To quickly tell if your ATV is getting spark, remove the spark plug from the engine. Reinsert the plug back into the coil wire. Hold the electrodes of the spark plug close to the engine to ground it, and try starting the engine. If you see spark coming from the end of the spark plug, your ATV engine is getting spark.
What kind of clutch does a Yamaha 600 Grizzly have?
2000 Yamaha 600 Grizzly Ultramatic. Shifter Assembly (OPS1078) 2000 Yamaha 600 Grizzly Ultramatic. Oil Cooler Radiator (OPS1078) 2000 Yamaha 600 Grizzly Ultramatic. Clutch Cover (OPS1078) 2000 Yamaha 600 Grizzly Ultramatic. Clutch Belt (OPS1078) Only 1 left!
How does the stator work on a Yamaha Grizzly?
Watch the video above and follow the guide below to test the stator for your Yamaha Grizzly. The Yamaha Grizzly stator is a set of three wire coils, or stator windings, that generate an AC electrical current. This current is sent to the regulator/rectifier, where it’s converted to DC current and then sent onto the battery.