How does the ignition switch work on a Harley Davidson?

This switch is specifically designed so that only the right key could complete the ignition circuit and power up the starter motor to crank the engine, then start and maintain the combustion cycle. If you turn your key but nothing happens even though the battery is fully charged, then the problem may lay in a faulty ignition switch.

Why does my Harley Davidson have no power?

Last Friday I shut the motor off with the stop switch and then turned the ignition key off. I re-set the stop switch to On. 1 minute later, I turned the ignition switch to ignition and noticed I had no power to my headlights and instrument lights.

Is there any power to the ignition switch?

I noticed that I had power from the accessory mode of the ignition switch. Horn, brake lights, turn signals have power. Bike is at home. This is what I tested (most with a meter) and cleaned: 1) Battery is good. 2) Battery cables and connections are good. 3) Stop or kill switch was taken apart and tested.

What should I do if I need to replace my ignition switch?

Reconnect the cable to the negative (-) terminal on the battery, then insert the key into the ignition and turn it to start the vehicle. The vehicle should start without any issue. If it doesn’t, remove the ignition switch and reinstall it. Shut the engine off (if it starts) and disconnect the battery again.

How to align ignition switch without ignition switch alignment tool?

Discussion in ‘ Electrical ‘ started by TQuentin1, Oct 21, 2017 . I need a hint on how to align the ignition switch without the Ignition Switch Alignment Tool (P/N HD-45962). They look something like the pix below.

Why is my ignition switch on the left?

Problem is that the fork is locked in the left most position, and I can’t get to the screw in the fork well that releases the outer fairing!!! One thing after another. Supposedly I have to take the outer fairing off, remove the radio and then release the wire harness connector from the switch housing.

Is there a video to replace the ignition switch?

I have a 2015 Electro glide, the cap turns to unlock position but the pin does not move. Is there a video that shows how to remove the switch housing to replace the actual switch ?

How do you remove the ignition knob on a Harley Davidson?

This is a modal window. This modal can be closed by pressing the Escape key or activating the close button. We have been asked a couple times about Harley-Davidson ignition switch knob removal in our Harley Tips section. Here’s a quick video on the topic.

Where is the ignition switch on a Harley Davidson?

The key on most Harley Touring bikes fits into a chrome turn piece, which actually turns the bike on and off. There are many reasons you may need to remove this bike knob, but no matter, if you have the key, you can remove it in minutes. This article applies to the Harley Davidson Touring (2000-2014).

How do you unlock the ignition on a Harley Davidson?

Inert your key into the ignition and turn to the “lock” position. Slide a finger under the bottom right edge of the ignition lock and feel for the tab. Turn the key a little passed “unlock” while pressing up on the tab, and the ignition key knob will pull straight up and out.

I have a 2015 Electro glide, the cap turns to unlock position but the pin does not move. Is there a video that shows how to remove the switch housing to replace the actual switch ?

What kind of ignition switch do you need for a motorcycle?

This universal motorcycle ignition switch is perfect for those of you out there who are minimalist. A simple momentary button that mounts directly to your solenoid. Just push and release, no key is needed.

Can a motorcycle ignition switch take a dump?

You rarely consider the ignition switch actually took a dump until you start tracing the problem. Out of all the things that can go wrong, your motorcycle ignition switch is pretty reliable. First part most people check when the bike won’t start is the motorcycle battery.

What kind of ignition switch does lowbrow customs use?

Lowbrow Customs also carries bolt-on and weld-on ignition mounting tabs. Perfect for motorcycle ignition key switch relocation jobs where you need to move the switch. If you are building a custom bike or just replacing a worn-out OEM ignition switch, we have the parts you need.

Which is the best ignition cover for a Harley Davidson?

Ensure your ride confidently roars to life with the top Harley-Davidson ignition switch models at excellent prices from J&P Cycles. Whether you’re replacing your existing Harley ignition system or in the middle of a custom build, each Harley-Davidson ignition switch cover is designed to operate smoothly and reliably.

How are spark plugs connected to the ignition system?

This system consists of an ignition switch that turns the motor on, kill switch that turns it off, ignition boxes and modules that manage the spark timing, ignition coils that produce high-voltage impulses, and spark plugs that transform these impulses into sparks. All these components are connected with wires.

What kind of spark plugs does a Harley Davidson use?

ACCEL Motorcycle S/S wire sets feature extra thick 8mm silicone jacket and silicon insulation to eliminate electrical leakage or RFI interference that interrupts electronic… Super Stock™ S/S Spark Plug Wire Set by Accel®.

Where can I buy a Harley Davidson ignition switch?

Go to Garage to select a motorcycle to ensure the best fitment. Ensure your ride confidently roars to life with the top Harley-Davidson ignition switch models at excellent prices from J&P Cycles.

Can a 3 pole ignition switch be used on a motorcycle?

We carry a variety of standard 3 pole switches which can be used as a custom motorcycle ignition switch on just about any bike. We also carry the direct solenoid starter button. This universal motorcycle ignition switch is perfect for those of you out there who are minimalist.

Navigation