Why is my starter not working on my Harley?
That black wire with the red tracer should be sending 12v to the starter relay. Be sure that this wire is not damaged or pinched anywhere in its travel. This will be more common when wires have been routed through the bars, or switch housings/switches have been changed. Don’t forget to use your multimeter inside the switch housings too.
Why does my starter turn over with the key?
If it turns over with the key, the switch is either bad or wired incorrectly. Solution #6: Confirm that you purchased a starter designed to work with your engine’s compression ratio. Engines with 11:1 or higher compression generally require a high-torque, gear-reduction starter. Otherwise, the engine will turn over slowly.
Why does my starter keep rotating After disengaging?
#2: The starter continues to rotate even after the drive gear disengages and start button has been released from the ‘on’ position. This is a symptom of burnt out contacts. It results from the contacts being exposed to high currents and heat over time causing the surfaces to melt and fuse together.
Where are the starter bolts on a Harley Davidson?
Remove all wiring connections from the starter solenoid and starter motor, using a combination wrench. Unscrew the starter mounting bolts using a socket wrench. The bolts are from the right side of the engine on most Harley-Davidson models; however, Sportster models locate the bolts within the primary chaincase on the left side of engine.
Are there any problems with the HD starter?
There are a few very common HD Starter problems. It starts with pushing the start button on only hearing a “click”. It’s a quick summary of these problems and the fixes for them Category Autos & Vehicles Show moreShow less Loading… AutoplayWhen autoplay is enabled, a suggested video will automatically play next. Up next
What are the symptoms of a Harley Davidson starter problem?
Harley Davidson Electra-Glide 1985 FLHT start clutch drive problem. Symptoms: When starter button is pressed there is a click and nothing happens or the starter drive tries to engage and then does not stay engaged. There is a lot of racket and noise like gears grinding.
What happens when you stop pressing the starter button?
Starter stays on after engine started. When you start your engine and release the key or stop pressing the starter button on a modern vehicle, the circuit is supposed to close, which will discontinue power to the starter motor.
Why is my starter relay not working properly?
Intermittent issues starting the vehicle If the starter relay is working properly, it will send power to the starter every time it is engaged. However, it is possible that the starter relay will become damaged due to excessive heat, dirt, and debris or other issues that might cause sporadic operation of the starter.
That black wire with the red tracer should be sending 12v to the starter relay. Be sure that this wire is not damaged or pinched anywhere in its travel. This will be more common when wires have been routed through the bars, or switch housings/switches have been changed. Don’t forget to use your multimeter inside the switch housings too.
What causes a Harley Davidson to not turn over?
If the bike does not turn over, the issue can be battery, starter, starter relay. If turns over, but no start, determine if the issue is electrical or fuel related. Check for spark.
What’s the voltage on a Harley Davidson starter?
I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.
Why is my Harley Davidson Ultra Classic not starting?
I have a 2010 ultra classic with ABS. It is not starting. The battery voltage is 12.75 off the battery. When I turn the main switch on, I get a drop to 12.5, and when the kill switch is turned on, I get a drop to 12.38. The self test goes out and hit the start switch with nothing – no volt drop, no starter engage, no nothing. DEAD.
What happens when the ignition switch is off?
Generally speaking, in the “OFF” position, the ignition switch doesn’t connect anything; in the “ACC” position, the radio or fan may be energized; in the “RUN” position, the engine control module is energized; and finally, in the “START” position, the starter relay is engaged. (These generalizations, depend significantly on year, make, and model.)
What happens if you hit the starter button and nothing happens?
Battery good, lights , horn turn signal works. Fuel pump runs , hit starter and nothing, lights do not dim and no sound at all. All fuses O.K. starter relay maybe ? any advice ? 06 roadking by the way.
Can a bad starter relay carry a test light?
Bad starter relay that is partially making contact to read voltage with a volt meter and turn on a test light but will not carry any load.
Generally speaking, in the “OFF” position, the ignition switch doesn’t connect anything; in the “ACC” position, the radio or fan may be energized; in the “RUN” position, the engine control module is energized; and finally, in the “START” position, the starter relay is engaged. (These generalizations, depend significantly on year, make, and model.)
Why is my Harley Davidson Dyna Glide not starting?
If your battery voltage and connections are in good condition, but your engine is still refusing to turn over, the problem may be in the starter circuit. Perhaps the easiest place to begin is at the starter solenoid on the right side of the motorcycle.
Where is the starter relay on a Dyna Glide?
Starter solenoid electrical connections. Another component to inspect is the starter relay, which is located in the electrical fuse box underneath the side cover on the left side of the motorcycle. Relays have the potential to go bad and prevent high current from reaching the starter.